> Have you tried asking the SATA card vendor (Promise or other > manufacturer) whether there is a compatibility issue with these drives?
> The Promise web site says WD Green drives are not suitable for use in > RAID mode, and this is a RAID controller. > Ben. I haven't talked to the vendor as the card is a no-name, but I did have it all working ok under Suse x86. I was running the card as two "single drive" striped raid arrays under x86 - two drives, each in its own "stripe array". Running through a linux setup messed a bit with the partition IDs (turned them to "promise-raid" IIRC) but that was interchangeable with a normal linux partition id- certainly didn't have problems recognising the disk itself. The stripe/mirror settings are configured via bios settings (which I wouldn't know how to get to on the G5) but the system works fine with smaller disks, so I assumed that config is functioning ok. However... I tried swapping out the previous sata card for an initio one: 0001:06:02.0 SATA controller: Initio Corporation INI-1623 PCI SATA-II Controller (rev 02) (prog-if 00 [Vendor specific]) Subsystem: Initio Corporation INI-1623 PCI SATA-II Controller Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 16, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 52 Region 0: I/O ports at 1000 [size=256] Region 1: I/O ports at 1100 [size=256] Region 2: I/O ports at 1200 [size=256] Region 3: I/O ports at 1300 [size=256] Region 4: I/O ports at 1400 [size=256] Region 5: Memory at 90000000 (32-bit, non-prefetchable) [size=4K] Expansion ROM at 90040000 [disabled] [size=256K] Capabilities: [dc] Power Management version 2 Flags: PMEClk+ DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: sata_inic162x --- I got the following dmesg which shows similar issues at [4.0...] and [9.53..] on ata7 I don't know if that sheds any light on anything or just muddies the waters. [ 0.000000] Allocated 20480 bytes for 32 pacas at c00000000fffb000 [ 0.000000] DART table allocated at: c00000007f000000 [ 0.000000] Using PowerMac machine description [ 0.000000] Page orders: linear mapping = 24, virtual = 12, io = 12, vmemmap = 24 [ 0.000000] Found initrd at 0xc000000002000000:0xc000000002b3dc00 [ 0.000000] Found U3 memory controller & host bridge @ 0xf8000000 revision: 0x35 [ 0.000000] Mapped at 0xd000080080000000 [ 0.000000] Found a K2 mac-io controller, rev: 96, mapped at 0xd000080080041000 [ 0.000000] PowerMac motherboard: PowerMac G5 [ 0.000000] DART IOMMU initialized for U3 type chipset [ 0.000000] bootconsole [udbg0] enabled [ 0.000000] CPU maps initialized for 1 thread per core [ 0.000000] (thread shift is 0) [ 0.000000] Freed 16384 bytes for unused pacas [ 0.000000] Starting Linux PPC64 #1 SMP Debian 3.2.32-1 [ 0.000000] ----------------------------------------------------- [ 0.000000] ppc64_pft_size = 0x0 [ 0.000000] physicalMemorySize = 0x100000000 [ 0.000000] htab_address = 0xc00000017c000000 [ 0.000000] htab_hash_mask = 0x7ffff [ 0.000000] ----------------------------------------------------- [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.2.0-4-powerpc64 (debian-ker...@lists.debian.org) (gcc version 4.6.3 (Debian 4.6.3-10) ) #1 SMP Debian 3.2.32-1 [ 0.000000] [boot]0012 Setup Arch [ 0.000000] Top of RAM: 0x180000000, Total RAM: 0x100000000 [ 0.000000] Memory hole size: 2048MB [ 0.000000] Found U3-AGP PCI host bridge. Firmware bus number: 240->255 [ 0.000000] PCI host bridge /pci@0,f0000000 ranges: [ 0.000000] MEM 0x00000000f1000000..0x00000000f1ffffff -> 0x00000000f1000000 [ 0.000000] IO 0x00000000f0000000..0x00000000f07fffff -> 0x0000000000000000 [ 0.000000] MEM 0x00000000b0000000..0x00000000cfffffff -> 0x00000000b0000000 [ 0.000000] Can't get bus-range for /ht@0,f2000000, assume bus 0 [ 0.000000] Found U3-HT PCI host bridge. Firmware bus number: 0->239 [ 0.000000] PCI host bridge /ht@0,f2000000 (primary) ranges: [ 0.000000] via-pmu: Server Mode is disabled [ 0.000000] PMU driver v2 initialized for Core99, firmware: 0c [ 0.000000] nvram: Checking bank 0... [ 0.000000] nvram: gen0=480, gen1=481 [ 0.000000] nvram: Active bank is: 1 [ 0.000000] nvram: OF partition at 0x410 [ 0.000000] nvram: XP partition at 0x1020 [ 0.000000] nvram: NR partition at 0x1120 [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0x00000000 -> 0x00180000 [ 0.000000] Normal empty [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[2] active PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00080000 [ 0.000000] 0: 0x00100000 -> 0x00180000 [ 0.000000] On node 0 totalpages: 1048576 [ 0.000000] DMA zone: 21504 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 1027072 pages, LIFO batch:31 [ 0.000000] [boot]0015 Setup Done [ 0.000000] PERCPU: Embedded 13 pages/cpu @c000000000b00000 s20608 r0 d32640 u524288 [ 0.000000] pcpu-alloc: s20608 r0 d32640 u524288 alloc=1*1048576 [ 0.000000] pcpu-alloc: [0] 0 1 [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 1027072 [ 0.000000] Policy zone: DMA [ 0.000000] Kernel command line: root=UUID=0f9ab1f7-7169-4686-a5c7-d3c91c176717 ro [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] freeing bootmem node 0 [ 0.000000] Memory: 4008076k/4194304k available (7048k kernel code, 186228k reserved, 1304k data, 1922k bss, 432k init) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] CONFIG_RCU_FANOUT set to non-default value of 32 [ 0.000000] RCU dyntick-idle grace-period acceleration is enabled. [ 0.000000] NR_IRQS:512 [ 0.000000] mpic: Resetting [ 0.000000] mpic: Setting up MPIC " MPIC 1 " version 1.2 at 80040000, max 2 CPUs [ 0.000000] mpic: ISU size: 120, shift: 7, mask: 7f [ 0.000000] mpic: Initializing for 120 sources [ 0.000000] mpic: Resetting [ 0.000000] mpic: Setting up MPIC " MPIC 2 " version 1.2 at f8040000, max 2 CPUs [ 0.000000] mpic: ISU size: 124, shift: 7, mask: 7f [ 0.000000] mpic: Initializing for 124 sources [ 0.000000] time_init: decrementer frequency = 33.333333 MHz [ 0.000000] time_init: processor frequency = 2300.000000 MHz [ 0.000000] clocksource: timebase mult[7800001] shift[22] registered [ 0.000000] clockevent: decrementer mult[8888887] shift[32] cpu[0] [ 0.000000] Console: colour dummy device 80x25 [ 0.000000] console [tty0] enabled, bootconsole disabled [ 0.001605] pid_max: default: 32768 minimum: 301 [ 0.001800] Security Framework initialized [ 0.001814] AppArmor: AppArmor disabled by boot time parameter [ 0.002461] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.006389] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.008172] Mount-cache hash table entries: 256 [ 0.011658] Initializing cgroup subsys cpuacct [ 0.011685] Initializing cgroup subsys memory [ 0.012041] Initializing cgroup subsys devices [ 0.012048] Initializing cgroup subsys freezer [ 0.012055] Initializing cgroup subsys net_cls [ 0.012062] Initializing cgroup subsys blkio [ 0.012078] Initializing cgroup subsys perf_event [ 0.012563] PowerMac SMP probe found 2 cpus [ 0.012702] KeyWest i2c @0xf8001003 irq 16 /u3@0,f8000000/i2c@f8001000 [ 0.012712] channel 0 bus <multibus> [ 0.012717] channel 1 bus <multibus> [ 0.012747] KeyWest i2c @0x80018000 irq 26 /ht@0,f2000000/pci@3/mac-io@7/i2c@18000 [ 0.012758] channel 0 bus <multibus> [ 0.012770] PMU i2c /ht@0,f2000000/pci@3/mac-io@7/via-pmu@16000/pmu-i2c [ 0.012780] channel 1 bus <multibus> [ 0.012786] channel 2 bus <multibus> [ 0.012852] Processor timebase sync using Pulsar i2c clock [ 0.012859] mpic: requesting IPIs... [ 0.012892] PPC970/FX/MP performance monitor hardware support registered [ 0.050655] Brought up 2 CPUs [ 0.051614] devtmpfs: initialized [ 0.060848] print_constraints: dummy: [ 0.061012] NET: Registered protocol family 16 [ 0.061033] IBM eBus Device Driver [ 0.061450] CPU Hotplug not supported by firmware - disabling. [ 0.063209] PCI: Probing PCI hardware [ 0.063414] pci 0000:f0:0b.0: [106b:0059] type 0 class 0x000600 [ 0.063502] pci 0000:f0:10.0: [1002:4e44] type 0 class 0x000300 [ 0.063523] pci 0000:f0:10.0: reg 10: [mem 0xc0000000-0xcfffffff pref] [ 0.063534] pci 0000:f0:10.0: reg 14: [io 0x0400-0x04ff] [ 0.063545] pci 0000:f0:10.0: reg 18: [mem 0xb0000000-0xb000ffff] [ 0.063574] pci 0000:f0:10.0: reg 30: [mem 0xb0020000-0xb003ffff pref] [ 0.063613] pci 0000:f0:10.0: supports D1 D2 [ 0.095793] IOMMU table initialized, virtual merging enabled [ 0.096090] pci 0001:00:00.0: [106b:0057] type 0 class 0x000600 [ 0.096131] pci 0001:00:01.0: [1022:7450] type 1 class 0x000604 [ 0.096209] pci 0001:00:02.0: [1022:7450] type 1 class 0x000604 [ 0.096281] pci 0001:00:03.0: [106b:0045] type 1 class 0x000604 [ 0.096371] pci 0001:00:04.0: [106b:0046] type 1 class 0x000604 [ 0.096446] pci 0001:00:05.0: [106b:0047] type 1 class 0x000604 [ 0.096523] pci 0001:00:06.0: [106b:0048] type 1 class 0x000604 [ 0.096599] pci 0001:00:07.0: [106b:0049] type 1 class 0x000604 [ 0.096724] pci 0001:06:02.0: [1101:1622] type 0 class 0x000106 [ 0.096738] pci 0001:06:02.0: reg 10: [io 0x1000-0x10ff] [ 0.096747] pci 0001:06:02.0: reg 14: [io 0x0c00-0x0cff] [ 0.096755] pci 0001:06:02.0: reg 18: [io 0x0800-0x08ff] [ 0.096764] pci 0001:06:02.0: reg 1c: [io 0x0400-0x04ff] [ 0.096772] pci 0001:06:02.0: reg 20: [io 0x0000-0x00ff] [ 0.096781] pci 0001:06:02.0: reg 24: [mem 0x90000000-0x90000fff] [ 0.096790] pci 0001:06:02.0: reg 30: [mem 0x90040000-0x9007ffff pref] [ 0.096814] pci 0001:06:02.0: supports D1 D2 [ 0.096818] pci 0001:06:02.0: PME# supported from D1 D2 D3hot [ 0.096848] pci 0001:06:03.0: [14e4:1644] type 0 class 0x000200 [ 0.096864] pci 0001:06:03.0: reg 10: [mem 0x90010000-0x9001ffff 64bit] [ 0.096926] pci 0001:06:03.0: PME# supported from D3hot D3cold [ 0.096950] pci 0001:00:01.0: PCI bridge to [bus 06-06] [ 0.096964] pci 0001:00:01.0: bridge window [mem 0x90000000-0x900fffff] [ 0.097044] pci 0001:07:04.0: [14e4:1644] type 0 class 0x000200 [ 0.097063] pci 0001:07:04.0: reg 10: [mem 0xa0000000-0xa000ffff 64bit] [ 0.097133] pci 0001:07:04.0: PME# supported from D3hot D3cold [ 0.097157] pci 0001:00:02.0: PCI bridge to [bus 07-07] [ 0.097170] pci 0001:00:02.0: bridge window [mem 0xa0000000-0xa00fffff] [ 0.097236] pci 0001:01:07.0: [106b:0041] type 0 class 0x00ff00 [ 0.097249] pci 0001:01:07.0: reg 10: [mem 0x80000000-0x8007ffff] [ 0.097314] pci 0001:01:08.0: [106b:0040] type 0 class 0x000c03 [ 0.097328] pci 0001:01:08.0: reg 10: [mem 0x80081000-0x80081fff] [ 0.097392] pci 0001:01:09.0: [106b:0040] type 0 class 0x000c03 [ 0.097407] pci 0001:01:09.0: reg 10: [mem 0x80080000-0x80080fff] [ 0.097467] pci 0001:00:03.0: PCI bridge to [bus 01-01] [ 0.097480] pci 0001:00:03.0: bridge window [mem 0x80000000-0x800fffff] [ 0.097560] pci 0001:02:0b.0: [1033:0035] type 0 class 0x000c03 [ 0.097578] pci 0001:02:0b.0: reg 10: [mem 0x80102000-0x80102fff] [ 0.097646] pci 0001:02:0b.0: supports D1 D2 [ 0.097651] pci 0001:02:0b.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.097679] pci 0001:02:0b.1: [1033:0035] type 0 class 0x000c03 [ 0.097697] pci 0001:02:0b.1: reg 10: [mem 0x80101000-0x80101fff] [ 0.097765] pci 0001:02:0b.1: supports D1 D2 [ 0.097769] pci 0001:02:0b.1: PME# supported from D0 D1 D2 D3hot D3cold [ 0.097798] pci 0001:02:0b.2: [1033:00e0] type 0 class 0x000c03 [ 0.097816] pci 0001:02:0b.2: reg 10: [mem 0x80100000-0x801000ff] [ 0.097883] pci 0001:02:0b.2: supports D1 D2 [ 0.097888] pci 0001:02:0b.2: PME# supported from D0 D1 D2 D3hot D3cold [ 0.097910] pci 0001:00:04.0: PCI bridge to [bus 02-02] [ 0.097924] pci 0001:00:04.0: bridge window [mem 0x80100000-0x801fffff] [ 0.097998] pci 0001:03:0d.0: [106b:0043] type 0 class 0x00ff00 [ 0.098011] pci 0001:03:0d.0: reg 10: [mem 0x80204000-0x80207fff] [ 0.098075] pci 0001:03:0e.0: [106b:0042] type 0 class 0x000c00 [ 0.098092] pci 0001:03:0e.0: reg 10: [mem 0x80200000-0x80200fff] [ 0.098155] pci 0001:03:0e.0: supports D1 D2 [ 0.098159] pci 0001:03:0e.0: PME# supported from D0 D1 D2 D3hot [ 0.098177] pci 0001:00:05.0: PCI bridge to [bus 03-03] [ 0.098191] pci 0001:00:05.0: bridge window [mem 0x80200000-0x802fffff] [ 0.098259] pci 0001:04:0f.0: [106b:004c] type 0 class 0x000200 [ 0.098273] pci 0001:04:0f.0: reg 10: [mem 0x80400000-0x805fffff] [ 0.098310] pci 0001:04:0f.0: reg 30: [mem 0x80300000-0x803fffff pref] [ 0.098333] pci 0001:00:06.0: PCI bridge to [bus 04-04] [ 0.098347] pci 0001:00:06.0: bridge window [mem 0x80300000-0x805fffff] [ 0.098404] pci 0001:05:0c.0: [1166:0240] type 0 class 0x000101 [ 0.098416] pci 0001:05:0c.0: reg 10: [io 0x0000-0x0007] [ 0.098426] pci 0001:05:0c.0: reg 14: [io 0x0000-0x0003] [ 0.098435] pci 0001:05:0c.0: reg 18: [io 0x0000-0x0007] [ 0.098445] pci 0001:05:0c.0: reg 1c: [io 0x0000-0x0003] [ 0.098454] pci 0001:05:0c.0: reg 20: [io 0x0000-0x000f] [ 0.098464] pci 0001:05:0c.0: reg 24: [mem 0x80600000-0x80601fff] [ 0.098500] pci 0001:00:07.0: PCI bridge to [bus 05-05] [ 0.098514] pci 0001:00:07.0: bridge window [mem 0x80600000-0x806fffff] [ 0.100129] PCI: Cannot allocate resource region 0 of device 0001:06:02.0, will remap [ 0.100141] PCI: Cannot allocate resource region 1 of device 0001:06:02.0, will remap [ 0.100151] PCI: Cannot allocate resource region 2 of device 0001:06:02.0, will remap [ 0.100160] PCI: Cannot allocate resource region 3 of device 0001:06:02.0, will remap [ 0.100209] PCI 0000:f0 Cannot reserve Legacy IO [io 0x10000-0x10fff] [ 0.100215] PCI: max bus depth: 1 pci_try_num: 2 [ 0.100259] pci 0001:00:01.0: BAR 13: assigned [io 0x812000-0x812fff] [ 0.100269] pci 0001:06:02.0: BAR 0: assigned [io 0x812000-0x8120ff] [ 0.100280] pci 0001:06:02.0: BAR 1: assigned [io 0x812100-0x8121ff] [ 0.100290] pci 0001:06:02.0: BAR 2: assigned [io 0x812200-0x8122ff] [ 0.100300] pci 0001:06:02.0: BAR 3: assigned [io 0x812300-0x8123ff] [ 0.100310] pci 0001:06:02.0: BAR 4: assigned [io 0x812400-0x8124ff] [ 0.100319] pci 0001:00:01.0: PCI bridge to [bus 06-06] [ 0.100328] pci 0001:00:01.0: bridge window [io 0x812000-0x812fff] [ 0.100336] pci 0001:00:01.0: bridge window [mem 0x90000000-0x900fffff] [ 0.100347] pci 0001:00:02.0: PCI bridge to [bus 07-07] [ 0.100355] pci 0001:00:02.0: bridge window [mem 0xa0000000-0xa00fffff] [ 0.100365] pci 0001:00:03.0: PCI bridge to [bus 01-01] [ 0.100374] pci 0001:00:03.0: bridge window [mem 0x80000000-0x800fffff] [ 0.100384] pci 0001:00:04.0: PCI bridge to [bus 02-02] [ 0.100392] pci 0001:00:04.0: bridge window [mem 0x80100000-0x801fffff] [ 0.100403] pci 0001:00:05.0: PCI bridge to [bus 03-03] [ 0.100411] pci 0001:00:05.0: bridge window [mem 0x80200000-0x802fffff] [ 0.100421] pci 0001:00:06.0: PCI bridge to [bus 04-04] [ 0.100429] pci 0001:00:06.0: bridge window [mem 0x80300000-0x805fffff] [ 0.100440] pci 0001:00:07.0: PCI bridge to [bus 05-05] [ 0.100448] pci 0001:00:07.0: bridge window [mem 0x80600000-0x806fffff] [ 0.100478] pci_bus 0000:f0: resource 0 [io 0x10000-0x80ffff] [ 0.100482] pci_bus 0000:f0: resource 1 [mem 0xf1000000-0xf1ffffff] [ 0.100487] pci_bus 0000:f0: resource 2 [mem 0xb0000000-0xcfffffff] [ 0.100492] pci_bus 0001:00: resource 0 [io 0x811000-0xc10fff] [ 0.100497] pci_bus 0001:00: resource 1 [mem 0xfa000000-0xffffffff] [ 0.100502] pci_bus 0001:00: resource 2 [mem 0x80000000-0xafffffff] [ 0.100507] pci_bus 0001:00: resource 3 [mem 0xd0000000-0xefffffff] [ 0.100512] pci_bus 0001:06: resource 0 [io 0x812000-0x812fff] [ 0.100517] pci_bus 0001:06: resource 1 [mem 0x90000000-0x900fffff] [ 0.100522] pci_bus 0001:07: resource 1 [mem 0xa0000000-0xa00fffff] [ 0.100527] pci_bus 0001:01: resource 1 [mem 0x80000000-0x800fffff] [ 0.100533] pci_bus 0001:02: resource 1 [mem 0x80100000-0x801fffff] [ 0.100538] pci_bus 0001:03: resource 1 [mem 0x80200000-0x802fffff] [ 0.100543] pci_bus 0001:04: resource 1 [mem 0x80300000-0x805fffff] [ 0.100548] pci_bus 0001:05: resource 1 [mem 0x80600000-0x806fffff] [ 0.100552] PCI: Probing PCI hardware done [ 0.103047] opal: Node not found [ 0.104599] bio: create slab <bio-0> at 0 [ 0.104965] vgaarb: device added: PCI:0000:f0:10.0,decodes=io+mem,owns=mem,locks=none [ 0.105021] vgaarb: loaded [ 0.105026] vgaarb: bridge control possible 0000:f0:10.0 [ 0.105302] SCSI subsystem initialized [ 0.105416] libata version 3.00 loaded. [ 0.105681] Switching to clocksource timebase [ 0.114474] NET: Registered protocol family 2 [ 0.114793] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.117383] TCP established hash table entries: 524288 (order: 11, 8388608 bytes) [ 0.124563] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 0.125981] TCP: Hash tables configured (established 524288 bind 65536) [ 0.125997] TCP reno registered [ 0.126029] UDP hash table entries: 2048 (order: 4, 65536 bytes) [ 0.126111] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes) [ 0.126432] NET: Registered protocol family 1 [ 0.126467] PCI: CLS mismatch (32 != 64), using 128 bytes [ 0.126479] pci 0001:00:01.0: MSI quirk detected; subordinate MSI disabled [ 0.126489] pci 0001:00:01.0: AMD8131 rev 12 detected; disabling PCI-X MMRBC [ 0.126499] pci 0001:00:02.0: MSI quirk detected; subordinate MSI disabled [ 0.126508] pci 0001:00:02.0: AMD8131 rev 12 detected; disabling PCI-X MMRBC [ 0.126552] pci 0001:01:08.0: enabling device (0000 -> 0002) [ 0.181749] pci 0001:01:09.0: enabling device (0000 -> 0002) [ 0.237729] pci 0001:02:0b.0: enabling device (0000 -> 0002) [ 0.293730] pci 0001:02:0b.1: enabling device (0000 -> 0002) [ 0.349728] pci 0001:02:0b.2: enabling device (0004 -> 0006) [ 0.349860] Unpacking initramfs... [ 0.693806] Freeing initrd memory: 11512k freed [ 0.749721] Registering G5 CPU frequency driver [ 0.749736] Frequency method: i2c/pfunc, Voltage method: i2c/pfunc [ 0.749746] Low: 1800 Mhz, High: 2300 Mhz, Cur: 1800 MHz [ 0.773778] Hypercall H_BEST_ENERGY not supported [ 0.774240] audit: initializing netlink socket (disabled) [ 0.774271] type=2000 audit(1353563533.735:1): initialized [ 0.816381] HugeTLB registered 16 MB page size, pre-allocated 0 pages [ 0.816953] VFS: Disk quotas dquot_6.5.2 [ 0.817054] Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.817218] msgmni has been set to 7852 [ 0.817550] alg: No test for stdrng (krng) [ 0.817635] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.817647] io scheduler noop registered [ 0.817653] io scheduler deadline registered [ 0.817698] io scheduler cfq registered (default) [ 0.818143] radeonfb 0000:f0:10.0: enabling device (0086 -> 0087) [ 1.016455] radeonfb: Found Open Firmware ROM Image [ 1.016470] radeonfb: Retrieved PLL infos from Open Firmware [ 1.016478] radeonfb: Reference=27.00 MHz (RefDiv=12) Memory=260.00 Mhz, System=260.00 MHz [ 1.016487] radeonfb: PLL min 20000 max 40000 [ 1.110777] i2c i2c-1: unable to read EDID block. [ 1.262774] i2c i2c-1: unable to read EDID block. [ 1.414774] i2c i2c-1: unable to read EDID block. [ 1.866854] i2c i2c-2: unable to read EDID block. [ 2.018774] i2c i2c-2: unable to read EDID block. [ 2.170774] i2c i2c-2: unable to read EDID block. [ 2.526713] radeonfb: Monitor 1 type CRT found [ 2.526719] radeonfb: Monitor 2 type no found [ 2.541741] Attempt to iounmap early bolted mapping at 0xd0000800800c1000 [ 2.547837] Console: switching to colour frame buffer device 80x30 [ 2.554301] radeonfb (0000:f0:10.0): ATI Radeon 4e44 "ND" [ 2.554807] vio_register_driver: driver hvc_console registering [ 2.554830] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 2.555595] pmac_zilog: 0.6 (Benjamin Herrenschmidt <b...@kernel.crashing.org>) [ 2.559512] ttyPZ0 at MMIO 0x80013020 (irq = 22) is a Z85c30 ESCC - Serial port [ 2.567351] ttyPZ1 at MMIO 0x80013000 (irq = 23) is a Z85c30 ESCC - Serial port [ 2.575529] Linux agpgart interface v0.103 [ 2.579590] agpgart-uninorth 0000:f0:0b.0: Apple U3H chipset [ 2.587703] agpgart-uninorth 0000:f0:0b.0: configuring for size idx: 64 [ 2.591810] agpgart-uninorth 0000:f0:0b.0: AGP aperture is 256M @ 0x0 [ 2.596003] MacIO PCI driver attached to K2 chipset [ 2.601125] pata-pci-macio 0001:03:0d.0: enabling device (0014 -> 0016) [ 2.617725] pata-pci-macio 0001:03:0d.0: Activating pata-macio chipset K2 ATA-6, Apple bus ID 3 [ 2.626314] scsi0 : pata_macio [ 2.630568] ata1: PATA max UDMA/100 irq 39 [ 2.634839] mousedev: PS/2 mouse device common for all mice [ 2.639291] rtc-generic rtc-generic: rtc core: registered rtc-generic as rtc0 [ 2.643871] TCP cubic registered [ 2.648225] NET: Registered protocol family 10 [ 2.653530] Mobile IPv6 [ 2.657927] NET: Registered protocol family 17 [ 2.662454] Registering the dns_resolver key type [ 2.667125] PM: Registered nosave memory: 000000007f000000 - 0000000080000000 [ 2.672106] PM: Hibernation image not present or could not be loaded. [ 2.672130] registered taskstats version 1 [ 2.677454] input: PMU as /devices/virtual/input/input0 [ 2.682311] Registered led device: pmu-led::front [ 2.682587] rtc-generic rtc-generic: setting system clock to 2012-11-22 05:52:16 UTC (1353563536) [ 2.692212] Initializing network drop monitor service [ 2.801458] Freeing unused kernel memory: 432k freed [ 2.835549] udevd[50]: starting version 175 [ 2.880022] sata_inic162x 0001:06:02.0: version 0.4 [ 2.880074] sata_inic162x 0001:06:02.0: enabling device (0004 -> 0007) [ 2.917489] sungem.c:v1.0 David S. Miller <da...@redhat.com> [ 2.920373] sata_svw 0001:05:0c.0: version 2.3 [ 2.933467] scsi2 : sata_inic162x [ 2.940884] temperature temperature: PowerMac G5 Thermal control driver 1.3 [ 2.945598] Detected fan controls: [ 2.950117] 0: PWM fan, id 1, location: BACKSIDE,SYS CTRLR FAN [ 2.954747] 1: RPM fan, id 2, location: DRIVE BAY [ 2.959355] 2: PWM fan, id 2, location: SLOT,PCI FAN [ 2.963861] 3: RPM fan, id 3, location: CPU A INTAKE [ 2.968257] 4: RPM fan, id 4, location: CPU A EXHAUST [ 2.972601] 5: RPM fan, id 5, location: CPU B INTAKE [ 2.975617] usbcore: registered new interface driver usbfs [ 2.975676] usbcore: registered new interface driver hub [ 2.982521] gem 0001:04:0f.0: eth0: Sun GEM (PCI) 10/100/1000BaseT Ethernet 00:11:24:38:73:78 [ 2.984924] usbcore: registered new device driver usb [ 2.986631] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.986732] ehci_hcd 0001:02:0b.2: EHCI Host Controller [ 2.986814] ehci_hcd 0001:02:0b.2: new USB bus registered, assigned bus number 1 [ 3.014930] 6: RPM fan, id 6, location: CPU B EXHAUST [ 3.017774] ehci_hcd 0001:02:0b.2: irq 63, io mem 0x80100000 [ 3.025769] ehci_hcd 0001:02:0b.2: USB 2.0 started, EHCI 1.00 [ 3.030227] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 3.034054] scsi1 : sata_svw [ 3.034221] scsi3 : sata_inic162x [ 3.034307] ata6: SATA max UDMA/133 mmio m4096@0x90000000 port 0x90000000 irq 52 [ 3.034313] ata7: SATA max UDMA/133 mmio m4096@0x90000000 port 0x90000040 irq 52 [ 3.034727] i2c i2c-0: therm_pm72: attach_adapter method is deprecated [ 3.034731] i2c i2c-0: Please use another way to instantiate your i2c_client [ 3.034737] i2c i2c-1: therm_pm72: attach_adapter method is deprecated [ 3.034741] i2c i2c-1: Please use another way to instantiate your i2c_client [ 3.034746] i2c i2c-2: therm_pm72: attach_adapter method is deprecated [ 3.034750] i2c i2c-2: Please use another way to instantiate your i2c_client [ 3.034755] i2c i2c-3: therm_pm72: attach_adapter method is deprecated [ 3.034759] i2c i2c-3: Please use another way to instantiate your i2c_client [ 3.095839] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.099128] scsi4 : sata_svw [ 3.099459] tg3.c:v3.121 (November 2, 2011) [ 3.099473] tg3 0001:06:03.0: enabling device (0004 -> 0006) [ 3.099836] scsi5 : sata_svw [ 3.100102] scsi6 : sata_svw [ 3.100201] ata2: SATA max UDMA/133 mmio m8192@0x80600000 port 0x80600000 irq 17 [ 3.100208] ata3: SATA max UDMA/133 mmio m8192@0x80600000 port 0x80600100 irq 17 [ 3.100214] ata4: SATA max UDMA/133 mmio m8192@0x80600000 port 0x80600200 irq 17 [ 3.100220] ata5: SATA max UDMA/133 mmio m8192@0x80600000 port 0x80600300 irq 17 [ 3.167787] usb usb1: Product: EHCI Host Controller [ 3.172897] usb usb1: Manufacturer: Linux 3.2.0-4-powerpc64 ehci_hcd [ 3.178131] usb usb1: SerialNumber: 0001:02:0b.2 [ 3.183540] hub 1-0:1.0: USB hub found [ 3.188574] hub 1-0:1.0: 5 ports detected [ 3.199436] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 3.204942] ohci_hcd 0001:01:08.0: OHCI Host Controller [ 3.209755] ohci_hcd 0001:01:08.0: new USB bus registered, assigned bus number 2 [ 3.219244] ohci_hcd 0001:01:08.0: irq 27, io mem 0x80081000 [ 3.297587] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 [ 3.302483] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.312044] usb usb2: Product: OHCI Host Controller [ 3.316892] usb usb2: Manufacturer: Linux 3.2.0-4-powerpc64 ohci_hcd [ 3.321736] usb usb2: SerialNumber: 0001:01:08.0 [ 3.328208] hub 2-0:1.0: USB hub found [ 3.332985] hub 2-0:1.0: 2 ports detected [ 3.337882] ohci_hcd 0001:01:09.0: OHCI Host Controller [ 3.342627] ohci_hcd 0001:01:09.0: new USB bus registered, assigned bus number 3 [ 3.352185] ohci_hcd 0001:01:09.0: irq 28, io mem 0x80080000 [ 3.421765] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 3.429557] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 [ 3.434384] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.443614] usb usb3: Product: OHCI Host Controller [ 3.448201] usb usb3: Manufacturer: Linux 3.2.0-4-powerpc64 ohci_hcd [ 3.452745] usb usb3: SerialNumber: 0001:01:09.0 [ 3.457409] hub 3-0:1.0: USB hub found [ 3.461771] hub 3-0:1.0: 2 ports detected [ 3.466229] ohci_hcd 0001:02:0b.0: OHCI Host Controller [ 3.470575] ohci_hcd 0001:02:0b.0: new USB bus registered, assigned bus number 4 [ 3.479327] ohci_hcd 0001:02:0b.0: irq 63, io mem 0x80102000 [ 3.483669] ata2.00: ATA-7: ST3750640AS, 3.AAE, max UDMA/133 [ 3.483675] ata2.00: 1465149168 sectors, multi 16: LBA48 NCQ (depth 0/32) [ 3.517735] ata6: SATA link down (SStatus 0 SControl 300) [ 3.558596] ata2.00: configured for UDMA/133 [ 3.565568] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 [ 3.570047] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.578777] usb usb4: Product: OHCI Host Controller [ 3.583189] usb usb4: Manufacturer: Linux 3.2.0-4-powerpc64 ohci_hcd [ 3.587646] usb usb4: SerialNumber: 0001:02:0b.0 [ 3.593838] hub 4-0:1.0: USB hub found [ 3.598437] hub 4-0:1.0: 3 ports detected [ 3.603073] ohci_hcd 0001:02:0b.1: OHCI Host Controller [ 3.607534] ohci_hcd 0001:02:0b.1: new USB bus registered, assigned bus number 5 [ 3.616329] ohci_hcd 0001:02:0b.1: irq 63, io mem 0x80101000 [ 3.693555] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001 [ 3.698042] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.706805] usb usb5: Product: OHCI Host Controller [ 3.711207] usb usb5: Manufacturer: Linux 3.2.0-4-powerpc64 ohci_hcd [ 3.715649] usb usb5: SerialNumber: 0001:02:0b.1 [ 3.720513] hub 5-0:1.0: USB hub found [ 3.724886] hub 5-0:1.0: 2 ports detected [ 4.037732] ata7: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 4.042264] ata7.00: failed to IDENTIFY (INIT_DEV_PARAMS failed, err_mask=0x80) [ 4.051223] ata7: unhandled interrupt: cmd=0xff irq_stat=0xa4 idma_stat=0xa0 [ 4.599107] tg3 0001:06:03.0: eth1: Tigon3 [partno(BCM95700A6) rev 7102] (PCI:66MHz:64-bit) MAC address 00:04:76:3b:07:a8 [ 4.608330] tg3 0001:06:03.0: eth1: attached PHY is 5401 (10/100/1000Base-T Ethernet) (WireSpeed[0], EEE[0]) [ 4.617779] tg3 0001:06:03.0: eth1: RXcsums[1] LinkChgREG[1] MIirq[1] ASF[0] TSOcap[0] [ 4.627425] tg3 0001:06:03.0: eth1: dma_rwctrl[76ff2d0f] dma_mask[64-bit] [ 4.632482] tg3 0001:07:04.0: enabling device (0004 -> 0006) [ 6.132363] tg3 0001:07:04.0: eth2: Tigon3 [partno(BCM95700A6) rev 7102] (PCIX:66MHz:64-bit) MAC address 00:04:76:3b:07:fd [ 6.142265] tg3 0001:07:04.0: eth2: attached PHY is 5401 (10/100/1000Base-T Ethernet) (WireSpeed[0], EEE[0]) [ 6.152452] tg3 0001:07:04.0: eth2: RXcsums[1] LinkChgREG[1] MIirq[1] ASF[0] TSOcap[0] [ 6.163062] tg3 0001:07:04.0: eth2: dma_rwctrl[76db1b0f] dma_mask[64-bit] [ 9.533736] ata7: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 9.539203] ata7.00: link online but device misclassified [ 9.539208] ata7: link online but 1 devices misclassified, retrying [ 9.544632] ata7: reset failed (errno=-11), retrying in 10 secs [ 19.541735] ata7: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 19.547233] ata7: unhandled interrupt: cmd=0xff irq_stat=0xa4 idma_stat=0xa0 [ 19.552646] ata7.00: failed to IDENTIFY (INIT_DEV_PARAMS failed, err_mask=0x80) [ 19.563373] ata7: limiting SATA link speed to 1.5 Gbps [ 25.037739] ata7: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 25.043368] ata7.00: failed to IDENTIFY (INIT_DEV_PARAMS failed, err_mask=0x80) [ 25.043375] ata7: unhandled interrupt: cmd=0xff irq_stat=0xa4 idma_stat=0xa0 [ 30.533734] ata7: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 30.539456] ata7.00: link online but device misclassified [ 30.539461] ata7: link online but 1 devices misclassified, retrying [ 30.545118] ata7: reset failed (errno=-11), retrying in 10 secs [ 40.541731] ata7: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 40.547282] ata7.00: link online but device misclassified [ 40.547287] ata7: link online but 1 devices misclassified, retrying [ 40.552758] ata7: reset failed (errno=-11), retrying in 10 secs [ 50.549732] ata7: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 50.555333] scsi 1:0:0:0: Direct-Access ATA ST3750640AS 3.AA PQ: 0 ANSI: 5 [ 50.885756] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 50.905188] ata3.00: ATA-8: WDC WD20EARS-00MVWB0, 51.0AB51, max UDMA/133 [ 50.910601] ata3.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 0/32) [ 50.922648] ata3.00: configured for UDMA/133 [ 50.928058] scsi 4:0:0:0: Direct-Access ATA WDC WD20EARS-00M 51.0 PQ: 0 ANSI: 5 [ 51.268688] ata4: SATA link down (SStatus 4 SControl 300) [ 51.604688] ata5: SATA link down (SStatus 4 SControl 300) [ 51.611923] firewire_ohci 0001:03:0e.0: enabling device (0000 -> 0002) [ 51.634358] sd 1:0:0:0: [sda] 1465149168 512-byte logical blocks: (750 GB/698 GiB) [ 51.644660] sd 1:0:0:0: [sda] Write Protect is off [ 51.644705] sd 4:0:0:0: [sdb] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) [ 51.644792] sd 4:0:0:0: [sdb] Write Protect is off [ 51.644797] sd 4:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 51.644834] sd 4:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 51.673899] firewire_ohci: Added fw-ohci device 0001:03:0e.0, OHCI v1.0, 8 IR + 8 IT contexts, quirks 0x0 [ 51.685042] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 51.685821] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 51.689699] sd 1:0:0:0: Attached scsi generic sg0 type 0 [ 51.689923] sd 4:0:0:0: Attached scsi generic sg1 type 0 [ 51.717245] sdb: sdb1 sdb2 sdb3 sdb4 < sdb5 sdb6 > [ 51.723523] sd 4:0:0:0: [sdb] Attached SCSI disk [ 51.728809] sda: [mac] sda1 sda2 sda3 sda4 sda5 sda6 sda7 [ 51.734695] sd 1:0:0:0: [sda] Attached SCSI disk [ 52.173960] firewire_core: created device fw0: GUID 001124fffe387378, S800 [ 52.431540] PM: Starting manual resume from disk [ 52.441507] PM: Hibernation image partition 8:3 present [ 52.441511] PM: Looking for hibernation image. [ 52.447985] PM: Image not found (code -22) [ 52.447989] PM: Hibernation image not present or could not be loaded. [ 52.497960] kjournald starting. Commit interval 5 seconds [ 52.502989] EXT3-fs (sda5): mounted filesystem with ordered data mode [ 54.347608] udevd[305]: starting version 175 [ 54.880400] i2c i2c-4: therm_pm72: attach_adapter method is deprecated [ 54.890115] i2c i2c-4: Please use another way to instantiate your i2c_client [ 54.895034] PowerMac i2c bus pmu 2 registered [ 54.900512] i2c i2c-5: therm_pm72: attach_adapter method is deprecated [ 54.905334] i2c i2c-5: Please use another way to instantiate your i2c_client [ 54.910137] PowerMac i2c bus pmu 1 registered [ 54.915081] i2c i2c-6: therm_pm72: attach_adapter method is deprecated [ 54.920066] i2c i2c-6: Please use another way to instantiate your i2c_client [ 54.925111] PowerMac i2c bus mac-io 0 registered [ 54.930202] i2c i2c-7: therm_pm72: attach_adapter method is deprecated [ 54.935289] i2c i2c-7: Please use another way to instantiate your i2c_client [ 54.940403] PowerMac i2c bus u3 1 registered [ 54.945441] i2c i2c-8: therm_pm72: attach_adapter method is deprecated [ 54.950548] i2c i2c-8: Please use another way to instantiate your i2c_client [ 54.956972] PowerMac i2c bus u3 0 registered [ 54.964810] i2c i2c-7: I2C write to 0x2f failed, err -27 [ 54.969820] Failure writing to FCU: -27 [ 54.969948] kfand: failed to start FCU [ 55.675705] snd-aoa-fabric-layout: Using PMF GPIOs [ 55.680616] i2c i2c-0: aoa_codec_tas: attach_adapter method is deprecated [ 55.685678] i2c i2c-0: Please use another way to instantiate your i2c_client [ 55.690687] i2c i2c-1: aoa_codec_tas: attach_adapter method is deprecated [ 55.695718] i2c i2c-1: Please use another way to instantiate your i2c_client [ 55.700787] i2c i2c-2: aoa_codec_tas: attach_adapter method is deprecated [ 55.705895] i2c i2c-2: Please use another way to instantiate your i2c_client [ 55.711000] i2c i2c-3: aoa_codec_tas: attach_adapter method is deprecated [ 55.716052] i2c i2c-3: Please use another way to instantiate your i2c_client [ 55.721053] i2c i2c-4: aoa_codec_tas: attach_adapter method is deprecated [ 55.726144] i2c i2c-4: Please use another way to instantiate your i2c_client [ 55.731257] i2c i2c-5: aoa_codec_tas: attach_adapter method is deprecated [ 55.736318] i2c i2c-5: Please use another way to instantiate your i2c_client [ 55.741335] i2c i2c-6: aoa_codec_tas: attach_adapter method is deprecated [ 55.746298] i2c i2c-6: Please use another way to instantiate your i2c_client [ 55.751238] snd-aoa-codec-tas: found 'deq' node [ 55.752262] snd-aoa-fabric-layout: can use this codec [ 55.821511] snd-aoa-codec-tas: tas found, addr 0x35 on /ht@0,f2000000/pci@3/mac-io@7/i2c@18000/deq@6a [ 55.821533] i2c i2c-7: aoa_codec_tas: attach_adapter method is deprecated [ 55.826541] i2c i2c-7: Please use another way to instantiate your i2c_client [ 55.831498] i2c i2c-8: aoa_codec_tas: attach_adapter method is deprecated [ 55.836427] i2c i2c-8: Please use another way to instantiate your i2c_client [ 57.340519] Adding 5859368k swap on /dev/sda3. Priority:-1 extents:1 across:5859368k [ 57.979794] EXT3-fs (sda5): using internal journal [ 58.341975] loop: module loaded [ 58.464204] snd-powermac no longer handles any machines with a layout-id property in the device-tree, use snd-aoa. [ 60.400520] EXT4-fs (sdb5): mounted filesystem with ordered data mode. Opts: (null) [ 60.453743] ISO 9660 Extensions: Microsoft Joliet Level 3 [ 60.475902] ISO 9660 Extensions: RRIP_1991A [ 60.556538] ISO 9660 Extensions: Microsoft Joliet Level 3 [ 60.597893] ISO 9660 Extensions: RRIP_1991A [ 60.824822] ISO 9660 Extensions: Microsoft Joliet Level 3 [ 60.917540] ISO 9660 Extensions: RRIP_1991A [ 61.015802] ISO 9660 Extensions: Microsoft Joliet Level 3 [ 61.030112] ISO 9660 Extensions: RRIP_1991A [ 62.214036] sungem_phy: PHY ID: 2062e0, addr: 1 [ 62.214292] gem 0001:04:0f.0: eth0: Found BCM5421-K2 PHY [ 62.223848] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 62.612593] ADDRCONF(NETDEV_UP): eth1: link is not ready [ 62.838675] ADDRCONF(NETDEV_UP): eth2: link is not ready [ 64.734549] tg3 0001:06:03.0: eth1: Link is up at 100 Mbps, full duplex [ 64.738770] tg3 0001:06:03.0: eth1: Flow control is off for TX and off for RX [ 64.743589] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready [ 65.833864] gem 0001:04:0f.0: eth0: Link is up at 100 Mbps, full-duplex [ 65.838210] gem 0001:04:0f.0: eth0: Pause is enabled (rxfifo: 10240 off: 7168 on: 5632) [ 65.852355] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 75.397713] eth1: no IPv6 routers present [ 76.645719] eth0: no IPv6 routers present [ 83.797349] RPC: Registered named UNIX socket transport module. [ 83.805932] RPC: Registered udp transport module. [ 83.810306] RPC: Registered tcp transport module. [ 83.814555] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 83.846196] FS-Cache: Loaded [ 83.901372] FS-Cache: Netfs 'nfs' registered for caching [ 83.923377] Installing knfsd (copyright (C) 1996 o...@monad.swb.de). [ 84.242811] fuse init (API version 7.17) [ 90.583248] [drm] Initialized drm 1.1.0 20060810 [ 90.742653] [drm] radeon defaulting to kernel modesetting. [ 90.742661] [drm] radeon kernel modesetting enabled. [ 91.318499] Bluetooth: Core ver 2.16 [ 91.318551] NET: Registered protocol family 31 [ 91.318555] Bluetooth: HCI device and connection manager initialized [ 91.318568] Bluetooth: HCI socket layer initialized [ 91.318573] Bluetooth: L2CAP socket layer initialized [ 91.318931] Bluetooth: SCO socket layer initialized [ 91.351933] Bluetooth: RFCOMM TTY layer initialized [ 91.351949] Bluetooth: RFCOMM socket layer initialized [ 91.351953] Bluetooth: RFCOMM ver 1.11 [ 91.357232] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 91.357241] Bluetooth: BNEP filters: protocol multicast [ 91.662684] lp: driver loaded but no devices found [ 99.026697] ondemand governor failed, too long transition latency of HW, fallback to performance governor [ 99.030330] ondemand governor failed, too long transition latency of HW, fallback to performance governor [ 99.350400] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory [ 99.378713] NFSD: starting 90-second grace period -- To UNSUBSCRIBE, email to debian-bugs-dist-requ...@lists.debian.org with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org