Package: linux-2.6 Version: 3.2.17-1 Severity: normal Hello,
the wacom tablet in my Thinkpad x220t stopped working after the update of linux-image-3.2.0-2-amd64 from version 3.2.17 to 3.2.18 (and 3.2.19). The same problem also occurs with linux-image-3.4-trunk-amd64 (version 3.4.1-1~experimental.1). With these kernels I experience the following behavior: lsusb recognizes my tablet as Bus 002 Device 004: ID 056a:00e6 Wacom Co., Ltd lsusb -t gives Port 5: Dev 4, If 0, Class=HID, Driver=, 12M instead of the expected Port 5: Dev 4, If 0, Class=HID, Driver=wacom, 12M and consequently the device does not work. During booting I see the following in /dev/log/syslog: input: Wacom ISDv4 E6 Pen as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.5/2-1.5:1.0/input/input7 However, afterwards the corresponding input directory and especially the file input/input7 is not there. Reloading the wacom module does not change the situation and only produces the following in /dev/log/syslog: usbcore: deregistering interface driver wacom usbcore: registered new interface driver wacom wacom: v1.53:USB Wacom tablet driver After going back to version 3.2.17 of linux-image-3.2.0-2-amd64 everything works again. The tablet also works with kernel 3.4.2 from kernel.org. This might indicate that the problem is related to the Debian specific changes of the wacom driver mentioned in the changelog of linux-image-3.2.0-2-amd64 (see also bug #671801), which are also present in linux-image-3.4-trunk-amd64. (Version 0.15.0+20120515-1 of xserver-xorg-input-wacom has been used for all observations mentioned above.) Best regards Nils -- Package-specific info: ** Version: Linux version 3.2.0-2-amd64 (Debian 3.2.17-1) (debian-ker...@lists.debian.org) (gcc version 4.6.3 (Debian 4.6.3-5) ) #1 SMP Sat May 12 23:08:28 UTC 2012 ** Command line: BOOT_IMAGE=/boot/vmlinuz-3.2.0-2-amd64 root=UUID=b85df6c7-1c58-4c42-8d8a-1b65258b864d ro quiet i915.i915_enable_rc6=1 ** Not tainted ** Kernel log: [ 3.417776] iwlwifi 0000:03:00.0: loaded firmware version 17.168.5.3 build 42301 [ 3.418241] Registered led device: phy0-led [ 3.418770] thinkpad_acpi: ThinkPad ACPI Extras v0.24 [ 3.418773] thinkpad_acpi: http://ibm-acpi.sf.net/ [ 3.418775] thinkpad_acpi: ThinkPad BIOS 8DET52WW (1.22 ), EC unknown [ 3.418778] thinkpad_acpi: Lenovo ThinkPad X220 Tablet, model 42992QG [ 3.419816] thinkpad_acpi: detected a 8-level brightness capable ThinkPad [ 3.420138] thinkpad_acpi: radio switch found; radios are enabled [ 3.420284] thinkpad_acpi: possible tablet mode switch found; ThinkPad in laptop mode [ 3.422479] thinkpad_acpi: rfkill switch tpacpi_bluetooth_sw: radio is blocked [ 3.423878] thinkpad_acpi: rfkill switch tpacpi_wwan_sw: radio is unblocked [ 3.424233] Registered led device: tpacpi::thinklight [ 3.424283] Registered led device: tpacpi::power [ 3.424304] usb 2-1.4: MAC-Address: 0x02:0x80:0x37:0xec:0x02:0x00 [ 3.424310] Registered led device: tpacpi::standby [ 3.424342] Registered led device: tpacpi::thinkvantage [ 3.424445] thinkpad_acpi: Standard ACPI backlight interface available, not loading native one [ 3.424769] cdc_ncm 2-1.4:1.6: usb0: register 'cdc_ncm' at usb-0000:00:1d.0-1.4, CDC NCM, 02:80:37:ec:02:00 [ 3.424807] usbcore: registered new interface driver cdc_ncm [ 3.425813] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs' [ 3.425974] thinkpad_acpi: Console audio control enabled, mode: monitor (read only) [ 3.427761] input: ThinkPad Extra Buttons as /devices/platform/thinkpad_acpi/input/input8 [ 3.872338] usb 1-1.4: new full-speed USB device number 5 using ehci_hcd [ 3.969548] usb 1-1.4: New USB device found, idVendor=0a5c, idProduct=217f [ 3.969552] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 3.969554] usb 1-1.4: Product: Broadcom Bluetooth Device [ 3.969555] usb 1-1.4: Manufacturer: Broadcom Corp [ 3.969556] usb 1-1.4: SerialNumber: EC55F9F6D0F3 [ 3.986718] Bluetooth: Core ver 2.16 [ 3.986736] NET: Registered protocol family 31 [ 3.986738] Bluetooth: HCI device and connection manager initialized [ 3.986741] Bluetooth: HCI socket layer initialized [ 3.986743] Bluetooth: L2CAP socket layer initialized [ 3.986749] Bluetooth: SCO socket layer initialized [ 3.988021] Bluetooth: Generic Bluetooth USB driver ver 0.6 [ 3.988253] usbcore: registered new interface driver btusb [ 4.318633] psmouse serio1: synaptics: Touchpad model: 1, fw: 8.0, id: 0x1e2b1, caps: 0xd001a3/0x940300/0x120c00 [ 4.318641] psmouse serio1: synaptics: serio: Synaptics pass-through port at isa0060/serio1/input0 [ 4.319026] fbcon: inteldrmfb (fb0) is primary device [ 4.378198] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input9 [ 4.498505] Console: switching to colour frame buffer device 170x48 [ 4.502119] fb0: inteldrmfb frame buffer device [ 4.502120] drm: registered panic notifier [ 4.524725] acpi device:01: registered as cooling_device4 [ 4.524893] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input10 [ 4.524969] ACPI: Video Device [VID] (multi-head: yes rom: no post: no) [ 4.525071] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0 [ 4.525251] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 [ 4.525319] snd_hda_intel 0000:00:1b.0: irq 46 for MSI/MSI-X [ 4.525348] snd_hda_intel 0000:00:1b.0: setting latency timer to 64 [ 5.064366] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input11 [ 5.069428] HDMI status: Codec=3 Pin=5 Presence_Detect=0 ELD_Valid=0 [ 5.069593] HDMI status: Codec=3 Pin=6 Presence_Detect=0 ELD_Valid=0 [ 5.069757] HDMI status: Codec=3 Pin=7 Presence_Detect=0 ELD_Valid=0 [ 5.069908] input: HDA Intel PCH HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12 [ 5.070031] input: HDA Intel PCH HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input13 [ 5.070094] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input14 [ 5.398552] Adding 11893756k swap on /dev/sda5. Priority:-1 extents:1 across:11893756k SS [ 5.408956] EXT4-fs (sda1): re-mounted. Opts: (null) [ 5.441250] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [ 5.454954] loop: module loaded [ 5.875981] RPC: Registered named UNIX socket transport module. [ 5.875984] RPC: Registered udp transport module. [ 5.875985] RPC: Registered tcp transport module. [ 5.875986] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 5.881985] FS-Cache: Loaded [ 5.891223] FS-Cache: Netfs 'nfs' registered for caching [ 5.897048] Installing knfsd (copyright (C) 1996 o...@monad.swb.de). [ 6.053738] fuse init (API version 7.17) [ 6.622183] e1000e 0000:00:19.0: irq 42 for MSI/MSI-X [ 6.677792] e1000e 0000:00:19.0: irq 42 for MSI/MSI-X [ 6.678547] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 6.681121] iwlwifi 0000:03:00.0: L1 Enabled; Disabling L0S [ 6.681320] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0 [ 6.964733] iwlwifi 0000:03:00.0: L1 Enabled; Disabling L0S [ 6.964927] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0 [ 7.089577] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 7.094527] ADDRCONF(NETDEV_UP): usb0: link is not ready [ 7.100877] cdc_ncm: usb0: network connection: disconnected [ 7.896512] input: ACPI Virtual Keyboard Device as /devices/virtual/input/input15 [ 8.170640] Bluetooth: RFCOMM TTY layer initialized [ 8.170644] Bluetooth: RFCOMM socket layer initialized [ 8.170646] Bluetooth: RFCOMM ver 1.11 [ 8.172582] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 8.172586] Bluetooth: BNEP filters: protocol multicast [ 8.282948] lp: driver loaded but no devices found [ 8.285677] ppdev: user-space parallel port driver [ 10.570618] usb 1-1.4: USB disconnect, device number 5 [ 12.002111] IBM TrackPoint firmware: 0x0e, buttons: 3/3 [ 12.339868] input: TPPS/2 IBM TrackPoint as /devices/platform/i8042/serio1/serio2/input/input16 [ 13.183011] ADDRCONF(NETDEV_UP): usb0: link is not ready [ 13.200063] colord[2284]: segfault at 8 ip 000000000040bc6d sp 00007fff41d749a0 error 4 in colord[400000+20000] [ 26.490007] wlan0: authenticate with 00:14:bf:3b:fa:cc (try 1) [ 26.494626] wlan0: authenticated [ 26.535831] wlan0: associate with 00:14:bf:3b:fa:cc (try 1) [ 26.539340] wlan0: RX AssocResp from 00:14:bf:3b:fa:cc (capab=0x411 status=0 aid=1) [ 26.539349] wlan0: associated [ 26.547163] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 38.082523] wlan0: no IPv6 routers present [ 1432.590069] reportbug[4488]: segfault at 3400000045 ip 00007fbbeca72e3a sp 00007fff1923d3e0 error 4 in libc-2.13.so[7fbbec9fd000+17d000] ** Model information sys_vendor: LENOVO product_name: 42992QG product_version: ThinkPad X220 Tablet chassis_vendor: LENOVO chassis_version: Not Available bios_vendor: LENOVO bios_version: 8DET52WW (1.22 ) board_vendor: LENOVO board_name: 42992QG board_version: Not Available ** Loaded modules: acpi_cpufreq mperf cpufreq_conservative cpufreq_userspace cpufreq_powersave cpufreq_stats parport_pc ppdev lp parport bnep rfcomm binfmt_misc uinput fuse nfsd nfs nfs_acl auth_rpcgss fscache lockd sunrpc kvm_intel kvm loop snd_hda_codec_hdmi snd_hda_codec_conexant btusb bluetooth arc4 thinkpad_acpi joydev nvram cdc_ncm usbnet mii snd_seq_midi snd_seq_midi_event snd_hda_intel wacom snd_hda_codec snd_hwdep snd_pcm_oss snd_mixer_oss cdc_acm cdc_wdm iwlwifi uvcvideo videodev snd_rawmidi v4l2_compat_ioctl32 media snd_pcm mac80211 snd_page_alloc snd_seq cfg80211 battery i915 snd_seq_device snd_timer psmouse drm_kms_helper snd pcspkr evdev serio_raw drm i2c_i801 soundcore rfkill ac iTCO_wdt i2c_algo_bit power_supply tpm_tis i2c_core iTCO_vendor_support tpm tpm_bios wmi video button processor ext4 crc16 jbd2 mbcache usbhid hid sd_mod crc_t10dif ahci libahci libata thermal thermal_sys ehci_hcd sdhci_pci sdhci mmc_core scsi_mod e1000e usbcore usb_common ** PCI devices: 00:00.0 Host bridge [0600]: Intel Corporation 2nd Generation Core Processor Family DRAM Controller [8086:0104] (rev 09) Subsystem: Lenovo Device [17aa:21db] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> Kernel driver in use: agpgart-intel 00:02.0 VGA compatible controller [0300]: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller [8086:0126] (rev 09) (prog-if 00 [VGA controller]) Subsystem: Lenovo Device [17aa:21db] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 44 Region 0: Memory at f0000000 (64-bit, non-prefetchable) [size=4M] Region 2: Memory at e0000000 (64-bit, prefetchable) [size=256M] Region 4: I/O ports at 5000 [size=64] Expansion ROM at <unassigned> [disabled] Capabilities: <access denied> Kernel driver in use: i915 00:16.0 Communication controller [0780]: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 [8086:1c3a] (rev 04) Subsystem: Lenovo Device [17aa:21db] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+ Latency: 0 Interrupt: pin A routed to IRQ 11 Region 0: Memory at f2525000 (64-bit, non-prefetchable) [size=16] Capabilities: <access denied> 00:16.3 Serial controller [0700]: Intel Corporation 6 Series/C200 Series Chipset Family KT Controller [8086:1c3d] (rev 04) (prog-if 02 [16550]) Subsystem: Lenovo Device [17aa:21db] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 19 Region 0: I/O ports at 50b0 [size=8] Region 1: Memory at f252c000 (32-bit, non-prefetchable) [size=4K] Capabilities: <access denied> Kernel driver in use: serial 00:19.0 Ethernet controller [0200]: Intel Corporation 82579LM Gigabit Network Connection [8086:1502] (rev 04) Subsystem: Lenovo Device [17aa:21ce] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 42 Region 0: Memory at f2500000 (32-bit, non-prefetchable) [size=128K] Region 1: Memory at f252b000 (32-bit, non-prefetchable) [size=4K] Region 2: I/O ports at 5080 [size=32] Capabilities: <access denied> Kernel driver in use: e1000e 00:1a.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 [8086:1c2d] (rev 04) (prog-if 20 [EHCI]) Subsystem: Lenovo Device [17aa:21db] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at f252a000 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci_hcd 00:1b.0 Audio device [0403]: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller [8086:1c20] (rev 04) Subsystem: Lenovo Device [17aa:21db] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 46 Region 0: Memory at f2520000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel 00:1c.0 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 [8086:1c10] (rev b4) (prog-if 00 [Normal decode]) Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:1c.1 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 [8086:1c12] (rev b4) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 Memory behind bridge: f2400000-f24fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:1c.3 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 [8086:1c16] (rev b4) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=05, subordinate=0c, sec-latency=0 I/O behind bridge: 00004000-00004fff Memory behind bridge: f1c00000-f23fffff Prefetchable memory behind bridge: 00000000f0400000-00000000f0bfffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:1c.4 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 5 [8086:1c18] (rev b4) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=0d, subordinate=0d, sec-latency=0 I/O behind bridge: 00003000-00003fff Memory behind bridge: f1400000-f1bfffff Prefetchable memory behind bridge: 00000000f0c00000-00000000f13fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:1d.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 [8086:1c26] (rev 04) (prog-if 20 [EHCI]) Subsystem: Lenovo Device [17aa:21db] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 23 Region 0: Memory at f2529000 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci_hcd 00:1f.0 ISA bridge [0601]: Intel Corporation QM67 Express Chipset Family LPC Controller [8086:1c4f] (rev 04) Subsystem: Lenovo Device [17aa:21db] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> 00:1f.2 SATA controller [0106]: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller [8086:1c03] (rev 04) (prog-if 01 [AHCI 1.0]) Subsystem: Lenovo Device [17aa:21db] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 43 Region 0: I/O ports at 50a8 [size=8] Region 1: I/O ports at 50bc [size=4] Region 2: I/O ports at 50a0 [size=8] Region 3: I/O ports at 50b8 [size=4] Region 4: I/O ports at 5060 [size=32] Region 5: Memory at f2528000 (32-bit, non-prefetchable) [size=2K] Capabilities: <access denied> Kernel driver in use: ahci 00:1f.3 SMBus [0c05]: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller [8086:1c22] (rev 04) Subsystem: Lenovo Device [17aa:21db] Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin C routed to IRQ 18 Region 0: Memory at f2524000 (64-bit, non-prefetchable) [size=256] Region 4: I/O ports at efa0 [size=32] Kernel driver in use: i801_smbus 03:00.0 Network controller [0280]: Intel Corporation Centrino Advanced-N 6205 [8086:0085] (rev 34) Subsystem: Intel Corporation Centrino Advanced-N 6205 AGN [8086:1311] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 45 Region 0: Memory at f2400000 (64-bit, non-prefetchable) [size=8K] Capabilities: <access denied> Kernel driver in use: iwlwifi 0d:00.0 System peripheral [0880]: Ricoh Co Ltd Device [1180:e823] (rev 07) (prog-if 01) Subsystem: Lenovo Device [17aa:21db] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at f1400000 (32-bit, non-prefetchable) [size=256] Capabilities: <access denied> Kernel driver in use: sdhci-pci ** USB devices: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 003: ID 147e:2016 Upek Biometric Touchchip/Touchstrip Fingerprint Sensor Bus 001 Device 004: ID 04f2:b217 Chicony Electronics Co., Ltd Lenovo Integrated Camera (0.3MP) Bus 002 Device 003: ID 0bdb:1911 Ericsson Business Mobile Networks BV Bus 002 Device 004: ID 056a:00e6 Wacom Co., Ltd -- System Information: Debian Release: wheezy/sid APT prefers testing APT policy: (900, 'testing') Architecture: amd64 (x86_64) Kernel: Linux 3.2.0-2-amd64 (SMP w/4 CPU cores) Locale: LANG=en_US.utf8, LC_CTYPE=en_US.utf8 (charmap=UTF-8) Shell: /bin/sh linked to /bin/dash Versions of packages linux-image-3.2.0-2-amd64 depends on: ii debconf [debconf-2.0] 1.5.43 ii initramfs-tools [linux-initramfs-tool] 0.106 ii kmod 8-2 ii linux-base 3.5 ii module-init-tools 8-2 Versions of packages linux-image-3.2.0-2-amd64 recommends: ii firmware-linux-free 3 Versions of packages linux-image-3.2.0-2-amd64 suggests: pn grub-pc 1.99-22 pn linux-doc-3.2 <none> Versions of packages linux-image-3.2.0-2-amd64 is related to: pn firmware-atheros <none> pn firmware-bnx2 <none> pn firmware-bnx2x <none> pn firmware-brcm80211 <none> pn firmware-intelwimax <none> pn firmware-ipw2x00 <none> pn firmware-ivtv <none> pn firmware-iwlwifi 0.35 pn firmware-libertas <none> pn firmware-linux 0.35 pn firmware-linux-nonfree 0.35 pn firmware-myricom <none> pn firmware-netxen <none> pn firmware-qlogic <none> pn firmware-ralink <none> pn firmware-realtek <none> pn xen-hypervisor <none> -- debconf information excluded -- To UNSUBSCRIBE, email to debian-bugs-dist-requ...@lists.debian.org with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
