Hello, Ok it works a lot better with :
setenv bootcmd_sata 'ide reset;ext2load ide 1:1 0x0800000 /uInitrd;ext2load ide 1:1 0x400000 /uImage;bootm 0x400000 0x800000' run bootcmd_sata The bootm need the initrd address too. Regards Francois On Sun, Jan 3, 2010 at 10:13 PM, Francois Lorrain <[email protected]> wrote: > Hello, > > I am familiar with Debian, but a bit inexperienced on debian ARM ... > I got a Open-RD Client (the one with the nice aluminium box) for > chrismas and I was able to install debian on the Open-Rd + E-Sata > disk connected to it but now I am unable to boot into this debian > installation. > > From the email referenced at > http://www.mail-archive.com/[email protected]/msg10262.html, > I went through the installation succesfully up to the reboot into your > new Debian Machine ( Remove the CD :-) > > I have the hard disk partionned with Partition 1 = /boot, Partition 2 > = swap, Partition 3 = LVM (same thing I would have done on a regular > PC ...) > > when I try to boot from U-boot, I get the following : > > __ __ _ _ > | \/ | __ _ _ ____ _____| | | > | |\/| |/ _` | '__\ \ / / _ \ | | > | | | | (_| | | \ V / __/ | | > |_| |_|\__,_|_| \_/ \___|_|_| > _ _ ____ _ > | | | | | __ ) ___ ___ | |_ > | | | |___| _ \ / _ \ / _ \| __| > | |_| |___| |_) | (_) | (_) | |_ > \___/ |____/ \___/ \___/ \__| > ** MARVELL BOARD: OpenRD-Client LE > > U-Boot 1.1.4 (Oct 27 2009 - 21:57:24) Marvell version: 3.4.19 > > U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFB00 > > Soc: 88F6281 A0 (DDR2) > CPU running @ 1200Mhz L2 running @ 400Mhz > SysClock = 400Mhz , TClock = 200Mhz > > DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 > DRAM CS[0] base 0x00000000 size 256MB > DRAM CS[1] base 0x10000000 size 256MB > DRAM Total size 512MB 16bit width > Addresses 8M - 0M are saved for the U-Boot usage. > Mem malloc Initialization (8M - 7M): Done > NAND:512 MB > Flash: 0 kB > > CPU : Marvell Feroceon (Rev 1) > > Streaming disabled > Write allocate disabled > > Module 0 is AUDIO > Module 1 is RGMII > > USB 0: host mode > PEX 0: PCI Express Root Complex Interface > PEX interface detected Link X1 > Net: egiga0 [PRIME], egiga1 > Hit any key to stop autoboot: 0 > Marvell>> printenv bootargs > bootargs=console=ttyS0,115200 > Marvell>> printenv bootcmd_sata > bootcmd_sata=ide reset; ext2load ide 1:1 0x0800000 /uInitrd; ext2load > ide 1:1 0x400000 /uImage; bootm 0x400000 > Marvell>> printenv mainlineLinux > mainlineLinux=yes > Marvell>> run bootcmd_sata > > Reset IDE: > Marvell Serial ATA Adapter > Integrated Sata device found > [0 1 0]: Enable DMA mode (6) > Device 1 @ 0 1: > Model: WDC WD5000AAKS-00TMA0 Firm: 12.01C01 Ser#: > WD-WCAPW0126862 > Type: Hard Disk > Supports 48-bit addressing > Capacity: 476940.0 MB = 465.7 GB (976773168 x 512) > > > 5223157 bytes read > > 1811960 bytes read > ## Booting image at 00400000 ... > Image Name: Debian kernel > Created: 2010-01-03 19:46:17 UTC > Image Type: ARM Linux Kernel Image (uncompressed) > Data Size: 1811896 Bytes = 1.7 MB > Load Address: 00008000 > Entry Point: 00008000 > Verifying Checksum ... OK > OK > > Starting kernel ... > > Uncompressing > Linux.................................................................................................................... > done, booting the kernel. > [ 0.000000] Initializing cgroup subsys cpuset > [ 0.000000] Initializing cgroup subsys cpu > [ 0.000000] Linux version 2.6.30-2-kirkwood (Debian 2.6.30-8) > ([email protected]) (gcc version 4.3.4 (Debian 4.3.4-3) ) #1 Sun Sep 27 > 22:57:55 UTC 2009 > [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), > cr=00053977 > [ 0.000000] CPU: VIVT data cache, VIVT instruction cache > [ 0.000000] Machine: Marvell OpenRD Client Board > [ 0.000000] Memory policy: ECC disabled, Data cache writeback > [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. > Total pages: 130048 > [ 0.000000] Kernel command line: console=ttyS0,115200 > [ 0.000000] NR_IRQS:114 > [ 0.000000] PID hash table entries: 2048 (order: 11, 8192 bytes) > [ 0.000000] Console: colour dummy device 80x30 > [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) > [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) > [ 0.010000] Memory: 256MB 256MB = 512MB total > [ 0.010000] Memory: 515584KB available (3232K code, 548K data, 120K > init, 0K highmem) > [ 0.010000] Calibrating delay loop... 1199.30 BogoMIPS (lpj=5996544) > [ 0.240000] Security Framework initialized > [ 0.240000] SELinux: Disabled at boot. > [ 0.240000] Mount-cache hash table entries: 512 > [ 0.240000] Initializing cgroup subsys ns > [ 0.240000] Initializing cgroup subsys cpuacct > [ 0.240000] Initializing cgroup subsys devices > [ 0.240000] Initializing cgroup subsys freezer > [ 0.240000] Initializing cgroup subsys net_cls > [ 0.240000] CPU: Testing write buffer coherency: ok > [ 0.240000] net_namespace: 1076 bytes > [ 0.240000] regulator: core version 0.5 > [ 0.240000] NET: Registered protocol family 16 > [ 0.240000] Kirkwood: MV88F6281-A0, TCLK=200000000. > [ 0.240000] Feroceon L2: Enabling L2 > [ 0.240000] Feroceon L2: Cache support initialised. > [ 0.240000] PCI: bus0: Fast back to back transfers disabled > [ 0.250000] bio: create slab <bio-0> at 0 > [ 0.250000] NET: Registered protocol family 2 > [ 0.250000] IP route cache hash table entries: 16384 (order: 4, 65536 > bytes) > [ 0.250000] TCP established hash table entries: 65536 (order: 7, > 524288 bytes) > [ 0.250000] TCP bind hash table entries: 65536 (order: 6, 262144 bytes) > [ 0.250000] TCP: Hash tables configured (established 65536 bind 65536) > [ 0.250000] TCP reno registered > [ 0.250000] NET: Registered protocol family 1 > [ 0.250000] NetWinder Floating Point Emulator V0.97 (double precision) > [ 0.250000] audit: initializing netlink socket (disabled) > [ 0.250000] type=2000 audit(0.250:1): initialized > [ 0.260000] VFS: Disk quotas dquot_6.5.2 > [ 0.260000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) > [ 0.260000] JFFS2 version 2.2. (NAND) (SUMMARY) �© 2001-2006 Red Hat, Inc. > [ 0.260000] msgmni has been set to 1007 > [ 0.260000] alg: No test for stdrng (krng) > [ 0.260000] Block layer SCSI generic (bsg) driver version 0.4 > loaded (major 253) > [ 0.260000] io scheduler noop registered > [ 0.260000] io scheduler anticipatory registered > [ 0.260000] io scheduler deadline registered > [ 0.260000] io scheduler cfq registered (default) > [ 0.270000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled > [ 0.270000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A > [ 0.270000] console [ttyS0] enabled > [ 0.570000] serial8250.1: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A > [ 0.580000] brd: module loaded > [ 0.590000] NAND device: Manufacturer ID: 0xad, Chip ID: 0xdc > (Hynix NAND 512MiB 3,3V 8-bit) > [ 0.590000] Scanning device for bad blocks > [ 0.660000] Bad eraseblock 1361 at 0x00000aa20000 > [ 0.730000] Bad eraseblock 2934 at 0x000016ec0000 > [ 0.780000] Creating 3 MTD partitions on "orion_nand": > [ 0.790000] 0x000000000000-0x000000100000 : "u-boot" > [ 0.790000] uncorrectable error : <5>0x000000100000-0x000000500000 : > "uImage" > [ 0.800000] ftl_cs: FTL header not found. > [ 0.810000] 0x000000500000-0x000020000000 : "root" > [ 0.810000] ftl_cs: FTL header not found. > [ 0.820000] mice: PS/2 mouse device common for all mice > [ 0.830000] rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0 > [ 0.830000] i2c /dev entries driver > [ 0.840000] cpuidle: using governor ladder > [ 0.840000] cpuidle: using governor menu > [ 0.840000] mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver > [ 0.850000] mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver > [ 0.900000] mv_xor mv_xor.0: Marvell XOR: ( xor cpy ) > [ 0.940000] mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy ) > [ 0.980000] mv_xor mv_xor.2: Marvell XOR: ( xor cpy ) > [ 1.020000] mv_xor mv_xor.3: Marvell XOR: ( xor fill cpy ) > [ 1.020000] TCP cubic registered > [ 1.030000] NET: Registered protocol family 17 > [ 1.030000] registered taskstats version 1 > [ 1.030000] rtc-mv rtc-mv: setting system clock to 2010-01-03 > 21:02:27 UTC (1262552547) > [ 1.040000] List of all partitions: > [ 1.050000] 1f00 1024 mtdblock0 (driver?) > [ 1.050000] 1f01 4096 mtdblock1 (driver?) > [ 1.060000] 1f02 519168 mtdblock2 (driver?) > [ 1.060000] No filesystem could mount root, tried: > [ 1.070000] Kernel panic - not syncing: VFS: Unable to mount root > fs on unknown-block(0,0) > [ 1.070000] [<c002cd68>] (unwind_backtrace+0x0/0xdc) from > [<c0287000>] (panic+0x34/0x120) > [ 1.080000] [<c0287000>] (panic+0x34/0x120) from [<c0008ebc>] > (mount_block_root+0x25c/0x2b4) > [ 1.090000] [<c0008ebc>] (mount_block_root+0x25c/0x2b4) from > [<c00090e4>] (prepare_namespace+0x164/0x1c8) > [ 1.100000] [<c00090e4>] (prepare_namespace+0x164/0x1c8) from > [<c0008410>] (kernel_init+0xc0/0xf0) > [ 1.110000] [<c0008410>] (kernel_init+0xc0/0xf0) from [<c0043000>] > (do_exit+0x0/0x640) > [ 1.120000] [<c0043000>] (do_exit+0x0/0x640) from [<df814780>] (0xdf814780) > > So U-Boot seems to find the right kernel from the hard disk but it > does not go very far... > > I am probably missing something simple ... > > I tried to set the bootargs to bootargs= 'console=ttyS0,115200 > root=/dev/mapper/SATA-root' with the same result ... > > It seems I am missing the link to the initrd. > > Can you help me out ? or explain how this machine is supposed to boot > into debian, ? > > Regards and Happy New Year ... > > Francois > -- To UNSUBSCRIBE, email to [email protected] with a subject of "unsubscribe". Trouble? Contact [email protected]
