> -----Original Message----- > From: cygwin-ow...@cygwin.com [mailto:cygwin-ow...@cygwin.com] On > Behalf Of Achim Gratz > Sent: Thursday, January 21, 2016 12:10 PM > To: cygwin@cygwin.com > Subject: Re: New cygwin install hanging on postinstall > > KARR, DAVID writes: > > While it's sitting here, I dumped out "/var/log/setup.log.full". > Here is the end of the file: > > ---------------- > > The following DLLs couldn't be rebased because they were in use: > > /usr/bin/cygssp-0.dll > > /usr/bin/cygperl5_22.dll > > /usr/bin/cyggcc_s-1.dll > > /usr/bin/cygcrypt-0.dll > > /usr/lib/perl5/vendor_perl/5.22/i686-cygwin-threads- > 64int/auto/List/Util/Util. > > dll > > /usr/lib/perl5/5.22/i686-cygwin-threads-64int/auto/IO/IO.dll > > /usr/lib/perl5/5.22/i686-cygwin-threads- > 64int/auto/File/Glob/Glob.dll > > /usr/lib/perl5/5.22/i686-cygwin-threads- > 64int/auto/Fcntl/Fcntl.dll > > /usr/lib/perl5/5.22/i686-cygwin-threads- > 64int/auto/Encode/Encode.dll > > /usr/lib/perl5/5.22/i686-cygwin-threads- > 64int/auto/Digest/MD5/MD5.dll > > /usr/lib/perl5/5.22/i686-cygwin-threads-64int/auto/Cwd/Cwd.dll > > 2016/01/21 09:15:40 running: C:\cygwin\bin\dash.exe > "/etc/postinstall/0p_texlive > > _prep.dash" > > 2016/01/21 09:19:20 note: Nothing needed to be installed > > 2016/01/21 09:19:20 Ending cygwin install > > ----------- > > So this isn't a fresh install and in fact there is not only some > Cygwin > process running but a full blown Perl that has loaded a number of > modules. How'd you manage to do that before Cygwin was ready > installing? Are you perhaps reporting from a follow-on invocation > of > setup.exe after the first install already failed?
Beats the heck out of me. I didn't have Cygwin installed. I ran the installer. It hung at this point. I eventually cancelled it, because it obviously wasn't going to complete. This output is from one of the later retries. I never attempted to run anything installed in cygwin, I'm just trying to complete the installation. > For your current case, you need to get rid of _all_ running Cygwin > processes. Best idea is to open a shell and issue > > /usr/bin/rebase-trigger fullrebase > /usr/bin/pkill . > > (you need to have procps installed for this command to be > available). > Then run setup again to have it re-do the rebase and run all > postinstall > scripts that failed before. But I'm still interested how that > initial > failure could have occured, so if you could maybe look in > /var/log/setup.log if something indicates what happened there that > would > be good. More weirdness. I ran a mintty window, and I ran those command lines, but it gives me lots of lines like this: ------------- 2 [main] bash 28452 child_info_fork::abort: C:\cygwin\bin\cygiconv-2.dll: Loaded to different address: parent(0x4D0000) != child(0x2E0000) bash: fork: retry: No child processes ------------- I don't believe either of these command lines did anything, but just to be sure, after I ran them I killed the window an reran setup, and got the same symptoms. -- Problem reports: http://cygwin.com/problems.html FAQ: http://cygwin.com/faq/ Documentation: http://cygwin.com/docs.html Unsubscribe info: http://cygwin.com/ml/#unsubscribe-simple