https://qa.mandrakesoft.com/show_bug.cgi?id=1075
------- Additional Comments From [EMAIL PROTECTED] 2003-02-21 19:14 ------- I reinstalled cooker in order to see if I could replicate this bug. I disconnected the printer from the computer during the installation, plugged it in while after the computer had rebooted and ran rpmdrake. Unfortunately, the setup failed and rpmdrake closed and I got the command line prompt back. Below are the messages on std. out/std. err and log messages. I tried to run printerdrake again, but it failed in the same manner. That is, it didn't install the rpms again, but the initial message about having detected the printer and the possible need of installing rpms appeared again, as did the final error message. ################### # std out and std err: rmmod: module lp is not loaded rmmod: module parport_pc is not loaded rmmod: module parport_probe is not loaded rmmod: module parport is not loaded modprobe: Can't locate module parport_probe modprobe: Can't locate module parport_probe rmmod: module parport_probe is not loaded installing /mnt/hd/cooker/cooker/i586/Mandrake/RPMS/printer-filters-1.0-94mdk.i586.rpm /mnt/hd/cooker/cooker/i586/Mandrake/RPMS/libijs0-0.34-34mdk.i586.rpm /mnt/hd/cooker/cooker/i586/Mandrake/RPMS/foomatic-db-3.0-0.beta1.20030213.1mdk.i586.rpm /mnt/hd/cooker/cooker/i586/Mandrake/RPMS/foomatic-filters-3.0-0.beta1.20030213.1mdk.i586.rpm /mnt/hd/cooker/cooker/i586/Mandrake/RPMS/foomatic-db-engine-3.0-0.beta1.20030213.1mdk.i586.rpm /mnt/hd/cooker/cooker/i586/Mandrake/RPMS/mpage-2.5.3-3mdk.i586.rpm rpm: no packages given for erase Cannot read printrc file! installing /mnt/hd/cooker/cooker/i586/Mandrake/RPMS/printer-testpages-1.0-94mdk.i586.rpm /mnt/hd/cooker/cooker/i586/Mandrake/RPMS/nmap-3.00-2mdk.i586.rpm /mnt/hd/cooker/cooker/i586/Mandrake/RPMS/scli-0.2.9-3mdk.i586.rpm /mnt/hd/cooker/cooker/i586/Mandrake/RPMS/printer-utils-1.0-94mdk.i586.rpm /mnt/hd/cooker/cooker/i586/Mandrake/RPMS/libgimp1.2_1-1.2.3-20mdk.i586.rpm rpm: no packages given for erase install-info: warning: no info dir entry in `/usr/share/info/scli.info.bz2' Can't locate object method "set" via package "MDK::Common::Func::before_leaving" at /usr/lib/libDrakX/printer/printerdrake.pm line 3290. ########################## # From /var/log/messages Feb 21 11:20:00 localhost printerdrake[1724]: ### Program is starting ### Feb 21 11:20:01 localhost printerdrake[1724]: running: rmmod lp Feb 21 11:20:01 localhost printerdrake[1724]: running: rmmod parport_pc Feb 21 11:20:01 localhost printerdrake[1724]: running: rmmod parport_probe Feb 21 11:20:01 localhost printerdrake[1724]: running: rmmod parport Feb 21 11:20:01 localhost printerdrake[1724]: running: /sbin/modprobe parport_pc Feb 21 11:20:01 localhost kernel: parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE] Feb 21 11:20:01 localhost kernel: parport0: irq 7 detected Feb 21 11:20:01 localhost kernel: parport0: Printer, HEWLETT-PACKARD DESKJET 830C Feb 21 11:20:01 localhost printerdrake[1724]: running: /sbin/modprobe lp Feb 21 11:20:01 localhost kernel: lp0: using parport0 (polling). Feb 21 11:20:01 localhost printerdrake[1724]: running: /sbin/modprobe parport_probe Feb 21 11:20:01 localhost printerdrake[1724]: running: /sbin/modprobe -n parport_probe Feb 21 11:20:02 localhost printerdrake[1724]: running: rmmod parport_probe Feb 21 11:20:06 localhost kernel: i810_audio: drain_dac, dma timeout? Feb 21 11:20:07 localhost printerdrake[1724]: running: /bin/rpm > /dev/null -q foomatic-db-engine foomatic-filters foomatic- db Feb 21 11:20:08 localhost printerdrake[1724]: installed packages foomatic-db-engine foomatic-filters foomatic-db Feb 21 11:20:33 localhost printerdrake[1724]: running: /bin/rpm > /dev/null -q gimp Feb 21 11:20:33 localhost printerdrake[1724]: running: /bin/rpm > /dev/null -q foomatic-db-engine foomatic-filters foomatic- db printer-utils printer-testpages nmap scli Feb 21 11:20:33 localhost printerdrake[1724]: installed packages foomatic-db-engine foomatic-filters foomatic-db printer-uti ls printer-testpages nmap scli ------- You are receiving this mail because: ------- You are on the CC list for the bug, or are watching someone who is. ------- Reminder: ------- assigned_to: [EMAIL PROTECTED] status: ASSIGNED creation_date: description: I am running current cooker and I have set up my HP Deskjet 832C as an available printer. I was given the choice between HP Deskjet Series CUPS v. 1.1 HP New Deskjet Series CUPS v. 1.1 and I chose the former since it seemed to be the default. I also chose the colormodel to be CMYK because it was the default. Then I printed the test page and all the black colors (the borders and the text) were blue instead of black. The resolution in the colored graphics seemed to be much below the 300 DPI that I had specified. I tried to switch to a grayscale colormodel and printed the test page, but it looked the same as with the CMYK colormodel.
