Yes.
These are the voltage readings with nothing connected on several power
supplies options I have:
Voltage Readings
Pin Function USB Power 5V 0.8A HUB 5V
8A power supply
P1-5 Vbus 0 0
0
P1-7 VIN 4.97 5.152
5.163
P1-14 3.3V 3.422 3.422
3.422
P 1.24 Vout 4.925 5.108
5.118
I can not talk to the pb when its on the 5V 8A, but nothing shows up in
either on usb power or on a usb power hub.
I just connected it to see if it had any voltage impact.
Thank you.
Pat
On Wednesday, June 2, 2021 at 12:01:12 PM UTC-7 [email protected] wrote:
> Have you tried connecting a Powered USB HUB to the USB board attached to
> the PocketBeagle so the WiFi module is not drawing current directly from
> the PB?
>
> It seems there is an over-current condition being reported:
> * 126.004560] usb usb2-port1: over-current condition*
>
> Cheers,
>
> Jon
>
> On Wed, Jun 2, 2021 at 10:19 AM Patrick Bolton <[email protected]>
> wrote:
>
>> I do not have a standoff on a pocket beagle.
>>
>> But the problem is recurring on all models right side up, upside down
>> with and without 2/4-port USB 2.0 HUB Cape for PocketBeagle from
>> microwavemont on Tindie
>> <https://www.tindie.com/products/microwavemont/24-port-usb-20-hub-cape-for-pocketbeagle/>
>> installed
>> or a female pin block that keeps any pins or pads from contacting the
>> static pad.
>>
>> lsusb -v & udevadm trigger --> dmesg below
>>
>> I simply can not believe that the random selection process of purchasing
>> 4 pb's over a course of a year yielded four defective devices in my
>> possession.
>>
>> OK, I'll admit it: I purchased 6 and burned up 2 pulling too much power
>> from a gpio. That's my simple attempt at humor.
>>
>>
>> [image: IMG_6921.jpg]
>>
>> root@beaglebone:/var/lib/cloud9# lsusb -v
>>
>> Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
>> Device Descriptor:
>> bLength 18
>> bDescriptorType 1
>> bcdUSB 2.00
>> bDeviceClass 9 Hub
>> bDeviceSubClass 0
>> bDeviceProtocol 1 Single TT
>> bMaxPacketSize0 64
>> idVendor 0x1d6b Linux Foundation
>> idProduct 0x0002 2.0 root hub
>> bcdDevice 4.19
>> iManufacturer 3 Linux 4.19.94-ti-r64 musb-hcd
>> iProduct 2 MUSB HDRC host driver
>> iSerial 1 musb-hdrc.1
>> bNumConfigurations 1
>> Configuration Descriptor:
>> bLength 9
>> bDescriptorType 2
>> wTotalLength 0x0019
>> bNumInterfaces 1
>> bConfigurationValue 1
>> iConfiguration 0
>> bmAttributes 0xe0
>> Self Powered
>> Remote Wakeup
>> MaxPower 0mA
>> Interface Descriptor:
>> bLength 9
>> bDescriptorType 4
>> bInterfaceNumber 0
>> bAlternateSetting 0
>> bNumEndpoints 1
>> bInterfaceClass 9 Hub
>> bInterfaceSubClass 0
>> bInterfaceProtocol 0 Full speed (or root) hub
>> iInterface 0
>> Endpoint Descriptor:
>> bLength 7
>> bDescriptorType 5
>> bEndpointAddress 0x81 EP 1 IN
>> bmAttributes 3
>> Transfer Type Interrupt
>> Synch Type None
>> Usage Type Data
>> wMaxPacketSize 0x0004 1x 4 bytes
>> bInterval 12
>> Hub Descriptor:
>> bLength 9
>> bDescriptorType 41
>> nNbrPorts 1
>> wHubCharacteristic 0x0011
>> Per-port power switching
>> No overcurrent protection
>> TT think time 8 FS bits
>> bPwrOn2PwrGood 5 * 2 milli seconds
>> bHubContrCurrent 0 milli Ampere
>> DeviceRemovable 0x02
>> PortPwrCtrlMask 0xff
>> Hub Port Status:
>> Port 1: 0000.010c power oc suspend
>> can't get device qualifier: Resource temporarily unavailable
>> can't get debug descriptor: Resource temporarily unavailable
>> Device Status: 0x0001
>> Self Powered
>>
>> Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
>> Device Descriptor:
>> bLength 18
>> bDescriptorType 1
>> bcdUSB 2.00
>> bDeviceClass 9 Hub
>> bDeviceSubClass 0
>> bDeviceProtocol 1 Single TT
>> bMaxPacketSize0 64
>> idVendor 0x1d6b Linux Foundation
>> idProduct 0x0002 2.0 root hub
>> bcdDevice 4.19
>> iManufacturer 3 Linux 4.19.94-ti-r64 musb-hcd
>> iProduct 2 MUSB HDRC host driver
>> iSerial 1 musb-hdrc.0
>> bNumConfigurations 1
>> Configuration Descriptor:
>> bLength 9
>> bDescriptorType 2
>> wTotalLength 0x0019
>> bNumInterfaces 1
>> bConfigurationValue 1
>> iConfiguration 0
>> bmAttributes 0xe0
>> Self Powered
>> Remote Wakeup
>> MaxPower 0mA
>> Interface Descriptor:
>> bLength 9
>> bDescriptorType 4
>> bInterfaceNumber 0
>> bAlternateSetting 0
>> bNumEndpoints 1
>> bInterfaceClass 9 Hub
>> bInterfaceSubClass 0
>> bInterfaceProtocol 0 Full speed (or root) hub
>> iInterface 0
>> Endpoint Descriptor:
>> bLength 7
>> bDescriptorType 5
>> bEndpointAddress 0x81 EP 1 IN
>> bmAttributes 3
>> Transfer Type Interrupt
>> Synch Type None
>> Usage Type Data
>> wMaxPacketSize 0x0004 1x 4 bytes
>> bInterval 12
>> Hub Descriptor:
>> bLength 9
>> bDescriptorType 41
>> nNbrPorts 1
>> wHubCharacteristic 0x0011
>> Per-port power switching
>> No overcurrent protection
>> TT think time 8 FS bits
>> bPwrOn2PwrGood 5 * 2 milli seconds
>> bHubContrCurrent 0 milli Ampere
>> DeviceRemovable 0x02
>> PortPwrCtrlMask 0xff
>> Hub Port Status:
>> Port 1: 0000.0100 power
>> can't get device qualifier: Resource temporarily unavailable
>> can't get debug descriptor: Resource temporarily unavailable
>> Device Status: 0x0001
>> Self Powered
>>
>>
>> root@beaglebone:/var/lib/cloud9# udevadm trigger
>> root@beaglebone:/var/lib/cloud9# dmesg
>> [ 0.000000] Booting Linux on physical CPU 0x0
>> [ 0.000000] Linux version 4.19.94-ti-r64 (voodoo@rpi4b4g-07) (gcc
>> version 8.3.0 (Debian 8.3.0-6)) #1buster SMP PREEMPT Fri May 21 23:57:28
>> UTC 2021
>> [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7),
>> cr=10c5387d
>> [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing
>> instruction cache
>> [ 0.000000] OF: fdt: Machine model: TI AM335x PocketBeagle
>> [ 0.000000] Memory policy: Data cache writeback
>> [ 0.000000] efi: Getting EFI parameters from FDT:
>> [ 0.000000] efi: UEFI not found.
>> [ 0.000000] cma: Reserved 48 MiB at 0x9c800000
>> [ 0.000000] On node 0 totalpages: 130560
>> [ 0.000000] Normal zone: 1148 pages used for memmap
>> [ 0.000000] Normal zone: 0 pages reserved
>> [ 0.000000] Normal zone: 130560 pages, LIFO batch:31
>> [ 0.000000] CPU: All CPU(s) started in SVC mode.
>> [ 0.000000] AM335X ES2.1 (sgx neon)
>> [ 0.000000] random: get_random_bytes called from
>> start_kernel+0xac/0x4c0 with crng_init=0
>> [ 0.000000] percpu: Embedded 17 pages/cpu s38988 r8192 d22452 u69632
>> [ 0.000000] pcpu-alloc: s38988 r8192 d22452 u69632 alloc=17*4096
>> [ 0.000000] pcpu-alloc: [0] 0
>> [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages:
>> 129412
>> [ 0.000000] Kernel command line: console=ttyO0,115200n8
>> root=/dev/mmcblk0p1 ro rootfstype=ext4 rootwait coherent_pool=1M
>> net.ifnames=0 lpj=1990656 rng_core.default_quality=100 quiet
>> [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144
>> bytes)
>> [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072
>> bytes)
>> [ 0.000000] Memory: 438104K/522240K available (13312K kernel code,
>> 1140K rwdata, 4340K rodata, 1024K init, 350K bss, 34984K reserved, 49152K
>> cma-reserved, 0K highmem)
>> [ 0.000000] Virtual kernel memory layout:
>> vector : 0xffff0000 - 0xffff1000 ( 4 kB)
>> fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
>> vmalloc : 0xe0000000 - 0xff800000 ( 504 MB)
>> lowmem : 0xc0000000 - 0xdfe00000 ( 510 MB)
>> pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
>> modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
>> .text : 0x(ptrval) - 0x(ptrval) (14304 kB)
>> .init : 0x(ptrval) - 0x(ptrval) (1024 kB)
>> .data : 0x(ptrval) - 0x(ptrval) (1141 kB)
>> .bss : 0x(ptrval) - 0x(ptrval) ( 351 kB)
>> [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
>> [ 0.000000] ftrace: allocating 42210 entries in 124 pages
>> [ 0.000000] rcu: Preemptible hierarchical RCU implementation.
>> [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=2 to
>> nr_cpu_ids=1.
>> [ 0.000000] Tasks RCU enabled.
>> [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16,
>> nr_cpu_ids=1
>> [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
>> [ 0.000000] IRQ: Found an INTC at 0x(ptrval) (revision 5.0) with 128
>> interrupts
>> [ 0.000000] OMAP clockevent source: timer2 at 24000000 Hz
>> [ 0.000020] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps
>> every 89478484971ns
>> [ 0.000039] clocksource: timer1: mask: 0xffffffff max_cycles:
>> 0xffffffff, max_idle_ns: 79635851949 ns
>> [ 0.000049] OMAP clocksource: timer1 at 24000000 Hz
>> [ 0.001524] timer_probe: no matching timers found
>> [ 0.001768] Console: colour dummy device 80x30
>> [ 0.001794] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0'
>> [ 0.001799] This ensures that you still see kernel messages. Please
>> [ 0.001803] update your kernel commandline.
>> [ 0.001961] Calibrating delay loop (skipped) preset value.. 995.32
>> BogoMIPS (lpj=1990656)
>> [ 0.001981] pid_max: default: 32768 minimum: 301
>> [ 0.002269] Security Framework initialized
>> [ 0.002285] Yama: becoming mindful.
>> [ 0.002430] AppArmor: AppArmor initialized
>> [ 0.002537] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
>> [ 0.002549] Mountpoint-cache hash table entries: 1024 (order: 0, 4096
>> bytes)
>> [ 0.003657] CPU: Testing write buffer coherency: ok
>> [ 0.003720] CPU0: Spectre v2: using BPIALL workaround
>> [ 0.004203] CPU0: thread -1, cpu 0, socket -1, mpidr 0
>> [ 0.025990] Setting up static identity map for 0x80100000 - 0x80100060
>> [ 0.033891] rcu: Hierarchical SRCU implementation.
>> [ 0.045112] EFI services will not be available.
>> [ 0.049901] smp: Bringing up secondary CPUs ...
>> [ 0.049915] smp: Brought up 1 node, 1 CPU
>> [ 0.049927] SMP: Total of 1 processors activated (995.32 BogoMIPS).
>> [ 0.049934] CPU: All CPU(s) started in SVC mode.
>> [ 0.051665] devtmpfs: initialized
>> [ 0.078240] VFP support v0.3: implementor 41 architecture 3 part 30
>> variant c rev 3
>> [ 0.078878] clocksource: jiffies: mask: 0xffffffff max_cycles:
>> 0xffffffff, max_idle_ns: 7645041785100000 ns
>> [ 0.078899] futex hash table entries: 256 (order: 2, 16384 bytes)
>> [ 0.082875] xor: automatically using best checksumming function neon
>> [ 0.082892] pinctrl core: initialized pinctrl subsystem
>> [ 0.084213] NET: Registered protocol family 16
>> [ 0.089465] DMA: preallocated 1024 KiB pool for atomic coherent
>> allocations
>> [ 0.160175] l4_wkup_cm:clk:0010:0: failed to disable
>> [ 0.212529] audit: initializing netlink subsys (disabled)
>> [ 0.217990] audit: type=2000 audit(0.204:1): state=initialized
>> audit_enabled=0 res=1
>> [ 0.221368] OMAP GPIO hardware version 0.1
>> [ 0.243694] hw-breakpoint: debug architecture 0x4 unsupported.
>> [ 0.270044] raid6: using algorithm neonx8 gen() 0 MB/s
>> [ 0.270057] raid6: .... xor() 0 MB/s, rmw enabled
>> [ 0.270065] raid6: using neon recovery algorithm
>> [ 0.278059] edma 49000000.edma: TI EDMA DMA engine driver
>> [ 0.283923] SCSI subsystem initialized
>> [ 0.286045] libata version 3.00 loaded.
>> [ 0.286355] usbcore: registered new interface driver usbfs
>> [ 0.286414] usbcore: registered new interface driver hub
>> [ 0.286535] usbcore: registered new device driver usb
>> [ 0.288508] omap_i2c 4802a000.i2c: bus 1 rev0.11 at 400 kHz
>> [ 0.289377] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 400 kHz
>> [ 0.290034] pps_core: LinuxPPS API ver. 1 registered
>> [ 0.290044] pps_core: Software ver. 5.3.6 - Copyright 2005-2007
>> Rodolfo Giometti <[email protected]>
>> [ 0.290073] PTP clock support registered
>> [ 0.290984] omap-mailbox 480c8000.mailbox: omap mailbox rev 0x400
>> [ 0.294253] Advanced Linux Sound Architecture Driver Initialized.
>> [ 0.295023] NetLabel: Initializing
>> [ 0.295034] NetLabel: domain hash size = 128
>> [ 0.295039] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO
>> [ 0.295129] NetLabel: unlabeled traffic allowed by default
>> [ 0.296204] clocksource: Switched to clocksource timer1
>> [ 0.458548] VFS: Disk quotas dquot_6.6.0
>> [ 0.458651] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096
>> bytes)
>> [ 0.459533] AppArmor: AppArmor Filesystem Enabled
>> [ 0.472479] NET: Registered protocol family 2
>> [ 0.473530] tcp_listen_portaddr_hash hash table entries: 512 (order:
>> 0, 6144 bytes)
>> [ 0.473568] TCP established hash table entries: 4096 (order: 2, 16384
>> bytes)
>> [ 0.473609] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
>> [ 0.473668] TCP: Hash tables configured (established 4096 bind 4096)
>> [ 0.473807] UDP hash table entries: 256 (order: 1, 8192 bytes)
>> [ 0.473832] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
>> [ 0.474181] NET: Registered protocol family 1
>> [ 0.487337] RPC: Registered named UNIX socket transport module.
>> [ 0.487347] RPC: Registered udp transport module.
>> [ 0.487352] RPC: Registered tcp transport module.
>> [ 0.487357] RPC: Registered tcp NFSv4.1 backchannel transport module.
>> [ 0.488392] Unpacking initramfs...
>> [ 0.884189] Freeing initrd memory: 6904K
>> [ 0.885100] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5
>> counters available
>> [ 0.888166] Initialise system trusted keyrings
>> [ 0.888760] workingset: timestamp_bits=14 max_order=17 bucket_order=3
>> [ 0.895897] zbud: loaded
>> [ 0.903403] NFS: Registering the id_resolver key type
>> [ 0.903448] Key type id_resolver registered
>> [ 0.903453] Key type id_legacy registered
>> [ 0.903480] nfs4filelayout_init: NFSv4 File Layout Driver
>> Registering...
>> [ 0.903830] fuse init (API version 7.27)
>> [ 0.914543] Key type asymmetric registered
>> [ 0.914558] Asymmetric key parser 'x509' registered
>> [ 0.914664] Block layer SCSI generic (bsg) driver version 0.4 loaded
>> (major 246)
>> [ 0.919026] io scheduler noop registered
>> [ 0.919037] io scheduler deadline registered
>> [ 0.919335] io scheduler cfq registered (default)
>> [ 0.919345] io scheduler mq-deadline registered
>> [ 0.922960] pinctrl-single 44e10800.pinmux: 142 pins, size 568
>> [ 0.931981] gpio-of-helper ocp:cape-universal: ready
>> [ 0.942016] Serial: 8250/16550 driver, 6 ports, IRQ sharing disabled
>> [ 0.945661] 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 30,
>> base_baud = 3000000) is a 8250
>> [ 0.955776] console [ttyS0] enabled
>> [ 0.957017] 48022000.serial: ttyS1 at MMIO 0x48022000 (irq = 31,
>> base_baud = 3000000) is a 8250
>> [ 0.958019] 48024000.serial: ttyS2 at MMIO 0x48024000 (irq = 32,
>> base_baud = 3000000) is a 8250
>> [ 0.958964] 481a8000.serial: ttyS4 at MMIO 0x481a8000 (irq = 33,
>> base_baud = 3000000) is a 8250
>> [ 0.962509] omap_rng 48310000.rng: Random Number Generator ver. 20
>> [ 0.963455] sdhci: Secure Digital Host Controller Interface driver
>> [ 0.963463] sdhci: Copyright(c) Pierre Ossman
>> [ 0.963938] omap_gpio 44e07000.gpio: Could not set line 6 debounce to
>> 200000 microseconds (-22)
>> [ 0.963949] omap_hsmmc 48060000.mmc: Got CD GPIO
>> [ 0.964752] omap_hsmmc 48060000.mmc: Linked as a consumer to
>> regulator.1
>> [ 0.965095] random: fast init done
>> [ 0.965455] random: crng init done
>> [ 0.991385] sdhci-pltfm: SDHCI platform and OF driver helper
>> [ 1.001238] eqep 48300180.eqep: ver. 1.0
>> [ 1.001262] eqep 48300180.eqep: unable to select pin group
>> [ 1.001502] eqep 48300180.eqep: count_mode:0
>> [ 1.001513] eqep 48300180.eqep: invert_qa:1
>> [ 1.001521] eqep 48300180.eqep: invert_qb:1
>> [ 1.001529] eqep 48300180.eqep: invert_qi:0
>> [ 1.001538] eqep 48300180.eqep: invert_qs:0
>> [ 1.001546] eqep 48300180.eqep: swap_inputs:0
>> [ 1.001555] eqep 48300180.eqep: QDECCTL:0x0180
>> [ 1.001563] eqep 48300180.eqep: QPOSINIT:0x00000000
>> [ 1.001571] eqep 48300180.eqep: QPOSMAX:0xffffffff
>> [ 1.001578] eqep 48300180.eqep: QPOSCNT:0x00000000
>> [ 1.001586] eqep 48300180.eqep: omit_interrupt:0
>> [ 1.001710] eqep 48300180.eqep: QEINT:0x0800
>> [ 1.001718] eqep 48300180.eqep: QUPRD:0x05f5e100
>> [ 1.001726] eqep 48300180.eqep: QEPCTL:0x009e write
>> [ 1.001734] eqep 48300180.eqep: QEPCTL:0x009e read
>> [ 1.001763] eqep 48300180.eqep: irq:101, clk_rate:100000000
>> [ 1.002080] eqep 48304180.eqep: ver. 1.0
>> [ 1.002098] eqep 48304180.eqep: unable to select pin group
>> [ 1.002231] eqep 48304180.eqep: count_mode:0
>> [ 1.002241] eqep 48304180.eqep: invert_qa:1
>> [ 1.002249] eqep 48304180.eqep: invert_qb:1
>> [ 1.002258] eqep 48304180.eqep: invert_qi:0
>> [ 1.002266] eqep 48304180.eqep: invert_qs:0
>> [ 1.002275] eqep 48304180.eqep: swap_inputs:0
>> [ 1.002282] eqep 48304180.eqep: QDECCTL:0x0180
>> [ 1.002290] eqep 48304180.eqep: QPOSINIT:0x00000000
>> [ 1.002297] eqep 48304180.eqep: QPOSMAX:0xffffffff
>> [ 1.002304] eqep 48304180.eqep: QPOSCNT:0x00000000
>> [ 1.002312] eqep 48304180.eqep: omit_interrupt:0
>> [ 1.002319] eqep 48304180.eqep: QEINT:0x0800
>> [ 1.002326] eqep 48304180.eqep: QUPRD:0x05f5e100
>> [ 1.002416] eqep 48304180.eqep: QEPCTL:0x009e write
>> [ 1.002424] eqep 48304180.eqep: QEPCTL:0x009e read
>> [ 1.002446] eqep 48304180.eqep: irq:102, clk_rate:100000000
>> [ 1.055043] mmc0: host does not support reading read-only switch,
>> assuming write-enable
>> [ 1.058182] mmc0: new high speed SDHC card at address aaaa
>> [ 1.069206] mmcblk0: mmc0:aaaa SC32G 29.7 GiB
>> [ 1.075394] libphy: Fixed MDIO Bus: probed
>> [ 1.076823] CAN device driver interface
>> [ 1.078338] c_can_platform 481cc000.can: c_can_platform device
>> registered (regs=a73e130a, irq=39)
>> [ 1.079460] c_can_platform 481d0000.can: c_can_platform device
>> registered (regs=1eaec869, irq=40)
>> [ 1.080713] mmcblk0: p1
>> [ 1.083543] usbcore: registered new interface driver smsc95xx
>> [ 1.085359] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
>> [ 1.085409] ehci-platform: EHCI generic platform driver
>> [ 1.085769] ehci-omap: OMAP-EHCI Host Controller driver
>> [ 1.086648] usbcore: registered new interface driver usb-storage
>> [ 1.090010] am335x-phy-driver 47401300.usb-phy: 47401300.usb-phy
>> supply vcc not found, using dummy regulator
>> [ 1.090198] am335x-phy-driver 47401300.usb-phy: Linked as a consumer
>> to regulator.0
>> [ 1.093768] musb-hdrc musb-hdrc.0: MUSB HDRC host driver
>> [ 1.093810] musb-hdrc musb-hdrc.0: new USB bus registered, assigned
>> bus number 1
>> [ 1.094153] usb usb1: New USB device found, idVendor=1d6b,
>> idProduct=0002, bcdDevice= 4.19
>> [ 1.094165] usb usb1: New USB device strings: Mfr=3, Product=2,
>> SerialNumber=1
>> [ 1.094173] usb usb1: Product: MUSB HDRC host driver
>> [ 1.094181] usb usb1: Manufacturer: Linux 4.19.94-ti-r64 musb-hcd
>> [ 1.094188] usb usb1: SerialNumber: musb-hdrc.0
>> [ 1.095039] hub 1-0:1.0: USB hub found
>> [ 1.095102] hub 1-0:1.0: 1 port detected
>> [ 1.097977] am335x-phy-driver 47401b00.usb-phy: 47401b00.usb-phy
>> supply vcc not found, using dummy regulator
>> [ 1.098165] am335x-phy-driver 47401b00.usb-phy: Linked as a consumer
>> to regulator.0
>> [ 1.101588] musb-hdrc musb-hdrc.1: MUSB HDRC host driver
>> [ 1.101628] musb-hdrc musb-hdrc.1: new USB bus registered, assigned
>> bus number 2
>> [ 1.101950] usb usb2: New USB device found, idVendor=1d6b,
>> idProduct=0002, bcdDevice= 4.19
>> [ 1.101961] usb usb2: New USB device strings: Mfr=3, Product=2,
>> SerialNumber=1
>> [ 1.101969] usb usb2: Product: MUSB HDRC host driver
>> [ 1.101976] usb usb2: Manufacturer: Linux 4.19.94-ti-r64 musb-hcd
>> [ 1.101984] usb usb2: SerialNumber: musb-hdrc.1
>> [ 1.102784] hub 2-0:1.0: USB hub found
>> [ 1.102848] hub 2-0:1.0: 1 port detected
>> [ 1.115208] omap_rtc 44e3e000.rtc: registered as rtc0
>> [ 1.116852] i2c /dev entries driver
>> [ 1.120756] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60
>> sec
>> [ 1.121387] softdog: initialized. soft_noboot=0 soft_margin=60 sec
>> soft_panic=0 (nowayout=0)
>> [ 1.125794] ledtrig-cpu: registered to indicate activity on CPUs
>> [ 1.126372] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2
>> [ 1.126738] omap-aes 53500000.aes: will run requests pump with
>> realtime priority
>> [ 1.129466] omap-sham 53100000.sham: hw accel on OMAP rev 4.3
>> [ 1.133314] hidraw: raw HID events driver (C) Jiri Kosina
>> [ 1.140873] gnss: GNSS driver registered with major 242
>> [ 1.148110] NET: Registered protocol family 10
>> [ 1.220152] Segment Routing with IPv6
>> [ 1.220445] mip6: Mobile IPv6
>> [ 1.220607] NET: Registered protocol family 17
>> [ 1.220640] can: controller area network core (rev 20170425 abi 9)
>> [ 1.220739] NET: Registered protocol family 29
>> [ 1.220838] 8021q: 802.1Q VLAN Support v1.8
>> [ 1.220926] Key type dns_resolver registered
>> [ 1.220934] mpls_gso: MPLS GSO support
>> [ 1.221198] ThumbEE CPU extension supported.
>> [ 1.221214] Registering SWP/SWPB emulation handler
>> [ 1.221225] omap_voltage_late_init: Voltage driver support not added
>> [ 1.229555] registered taskstats version 1
>> [ 1.229565] Loading compiled-in X.509 certificates
>> [ 1.229702] zswap: loaded using pool lzo/zbud
>> [ 1.233195] Btrfs loaded, crc32c=crc32c-generic
>> [ 1.233320] AppArmor: AppArmor sha1 policy hashing enabled
>> [ 1.255554] musb-hdrc musb-hdrc.1: VBUS_ERROR in a_wait_vrise (81,
>> <SessEnd), retry #1, port1 00000104
>> [ 1.289902] tps6521x_pwrbutton tps65217-pwrbutton: DMA mask not set
>> [ 1.290734] input: tps65217_pwr_but as
>> /devices/platform/ocp/44e0b000.i2c/i2c-0/0-0024/tps65217-pwrbutton/input/input0
>> [ 1.291675] tps65217 0-0024: TPS65217 ID 0xe version 1.2
>> [ 1.292767] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1
>> bytes/write
>> [ 1.292886] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz
>> [ 1.293867] cpu cpu0: Linked as a consumer to regulator.3
>> [ 1.293974] cpu cpu0: Dropping the link to regulator.3
>> [ 1.294497] cpu cpu0: Linked as a consumer to regulator.3
>> [ 1.296781] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01
>> 00:00:01 UTC (946684801)
>> [ 1.297998] ALSA device list:
>> [ 1.298007] No soundcards found.
>> [ 1.304667] Freeing unused kernel memory: 1024K
>> [ 1.305396] Run /init as init process
>> [ 1.407989] musb-hdrc musb-hdrc.1: VBUS_ERROR in a_wait_vrise (81,
>> <SessEnd), retry #2, port1 00000104
>> [ 1.560416] musb-hdrc musb-hdrc.1: VBUS_ERROR in a_wait_vrise (81,
>> <SessEnd), retry #3, port1 00000104
>> [ 1.712848] musb-hdrc musb-hdrc.1: VBUS_ERROR in a_wait_vrise (80,
>> <SessEnd), retry #3, port1 0008010c
>> [ 8.712579] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data
>> mode. Opts: (null)
>> [ 9.506738] systemd[1]: System time before build time, advancing clock.
>> [ 9.562147] systemd[1]: systemd 241 running in system mode. (+PAM
>> +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP
>> +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN
>> -PCRE2 default-hierarchy=hybrid)
>> [ 9.562865] systemd[1]: Detected architecture arm.
>> [ 9.590814] systemd[1]: Set hostname to <beaglebone>.
>> [ 11.110862] systemd[1]: Set up automount Arbitrary Executable File
>> Formats File System Automount Point.
>> [ 11.112129] systemd[1]: Listening on udev Kernel Socket.
>> [ 11.119346] systemd[1]: Created slice system-serial\x2dgetty.slice.
>> [ 11.121983] systemd[1]: Created slice User and Session Slice.
>> [ 11.122153] systemd[1]: Reached target Slices.
>> [ 11.122252] systemd[1]: Reached target Swap.
>> [ 11.122810] systemd[1]: Started Forward Password Requests to Wall
>> Directory Watch.
>> [ 12.039029] EXT4-fs (mmcblk0p1): re-mounted. Opts: errors=remount-ro
>> [ 13.107843] systemd-journald[829]: Received request to flush runtime
>> journal from PID 1
>> [ 22.681928] using random self ethernet address
>> [ 22.681945] using random host ethernet address
>> [ 23.060030] Mass Storage Function, version: 2009/09/11
>> [ 23.060054] LUN: removable file: (no medium)
>> [ 23.399756] using random self ethernet address
>> [ 23.399775] using random host ethernet address
>> [ 23.622530] usb0: HOST MAC 60:64:05:5b:24:0d
>> [ 23.628884] usb0: MAC 60:64:05:5b:24:0c
>> [ 23.640690] usb1: HOST MAC 60:64:05:5b:24:0f
>> [ 23.641005] usb1: MAC 60:64:05:5b:24:10
>> [ 23.886192] IPv6: ADDRCONF(NETDEV_UP): usb0: link is not ready
>> [ 24.013118] configfs-gadget gadget: high-speed config #1: c
>> [ 24.013488] IPv6: ADDRCONF(NETDEV_CHANGE): usb0: link becomes ready
>> [ 24.159712] IPv6: ADDRCONF(NETDEV_UP): usb1: link is not ready
>> [ 54.719227] pvrsrvkm: loading out-of-tree module taints kernel.
>> [ 55.037101] [drm] Initialized pvr 1.17.4948957 20110701 for
>> 56000000.sgx on minor 0
>> [ 60.828113] remoteproc remoteproc0: wkup_m3 is available
>> [ 61.128477] remoteproc remoteproc0: powering up wkup_m3
>> [ 61.128512] remoteproc remoteproc0: Booting fw image
>> am335x-pm-firmware.elf, size 217148
>> [ 61.128804] remoteproc remoteproc0: remote processor wkup_m3 is now up
>> [ 61.128834] wkup_m3_ipc 44e11324.wkup_m3_ipc: CM3 Firmware Version =
>> 0x192
>> [ 61.217546] PM: bootloader does not support rtc-only!
>> [ 63.150834] remoteproc remoteproc1: 4a334000.pru is available
>> [ 63.151031] pru-rproc 4a334000.pru: PRU rproc node pru@4a334000 probed
>> successfully
>> [ 63.164515] remoteproc remoteproc2: 4a338000.pru is available
>> [ 63.164711] pru-rproc 4a338000.pru: PRU rproc node pru@4a338000 probed
>> successfully
>> [ 126.004560] usb usb2-port1: over-current condition
>> [ 126.048748] musb-hdrc musb-hdrc.1: VBUS_ERROR in a_wait_vrise (81,
>> <SessEnd), retry #1, port1 0000010c
>> [ 126.201173] musb-hdrc musb-hdrc.1: VBUS_ERROR in a_wait_vrise (81,
>> <SessEnd), retry #2, port1 0000010c
>> [ 126.353599] musb-hdrc musb-hdrc.1: VBUS_ERROR in a_wait_vrise (81,
>> <SessEnd), retry #3, port1 0000010c
>> [ 126.506031] musb-hdrc musb-hdrc.1: VBUS_ERROR in a_wait_vrise (80,
>> <SessEnd), retry #3, port1 0008010c
>>
>> On Wednesday, June 2, 2021 at 9:59:30 AM UTC-7 Dennis Bieber wrote:
>>
>>> On Tue, 1 Jun 2021 09:33:31 -0700 (PDT), in
>>> gmane.comp.hardware.beagleboard.user Patrick Bolton
>>> <[email protected]> wrote:
>>>
>>> >This morning, I setup a brand spanking new pocketbeagle straight out of
>>> >the package and have very concerning errors on installation of the most
>>> >recent image. Nothing whatsoever is connected other than the USB cable
>>> to
>>> >my PC. And the device is sitting on a grounded anti-static pad.
>>> >
>>>
>>> Do you have standoffs on that board...Sitting on an anti-static pad
>>> could be making contact with some underside circuitry, causing
>>> unexpected
>>> voltages on some pins.
>>>
>>>
>>> --
>>> Dennis L Bieber
>>>
>>> --
>> For more options, visit http://beagleboard.org/discuss
>> ---
>> You received this message because you are subscribed to the Google Groups
>> "BeagleBoard" group.
>> To unsubscribe from this group and stop receiving emails from it, send an
>> email to [email protected].
>> To view this discussion on the web visit
>> https://groups.google.com/d/msgid/beagleboard/77469212-0bbf-48fa-b3b6-56fcabd4efd3n%40googlegroups.com
>>
>> <https://groups.google.com/d/msgid/beagleboard/77469212-0bbf-48fa-b3b6-56fcabd4efd3n%40googlegroups.com?utm_medium=email&utm_source=footer>
>> .
>>
>
--
For more options, visit http://beagleboard.org/discuss
---
You received this message because you are subscribed to the Google Groups
"BeagleBoard" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to [email protected].
To view this discussion on the web visit
https://groups.google.com/d/msgid/beagleboard/00be9ecc-5813-4b29-b43d-bb319ced3a71n%40googlegroups.com.
