Hi,
I have Gentoo installed on an SD card for my BBB. After a kernel upgrade,
for some reason it seems like the board is loading the kernel from the SD
card, but booting into Debian on the EMMC.
Here's the log, I cut off where userspace begins for brevity, but please
let me know if it would be helpful and I can reply back with it.
U-Boot SPL 2019.04-dirty (Aug 16 2020 - 22:13:13 -0400)
Trying to boot from MMC1
Loading Environment from EXT4... ** File not found /boot/uboot.env **
** Unable to read "/boot/uboot.env" from mmc0:1 **
U-Boot 2019.04-dirty (Aug 16 2020 - 22:13:13 -0400)
CPU : AM335X-GP rev 2.1
I2C: ready
DRAM: 512 MiB
No match for driver 'omap_hsmmc'
No match for driver 'omap_hsmmc'
Some drivers were not found
Reset Source: Power-on reset has occurred.
RTC 32KCLK Source: External.
MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1
Loading Environment from EXT4... ** File not found /boot/uboot.env **
** Unable to read "/boot/uboot.env" from mmc0:1 **
Board: BeagleBone Black
<ethaddr> not set. Validating first E-fuse MAC
BeagleBone Black:
BeagleBone: cape eeprom: i2c_probe: 0x54:
BeagleBone: cape eeprom: i2c_probe: 0x55:
BeagleBone: cape eeprom: i2c_probe: 0x56:
BeagleBone: cape eeprom: i2c_probe: 0x57:
Net: eth0: MII MODE
cpsw, usb_ether
Press SPACE to abort autoboot in 2 seconds
board_name=[A335BNLT] ...
board_rev=[000C] ...
switch to partitions #0, OK
mmc0 is current device
SD/MMC found on device 0
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
gpio: pin 56 (gpio 56) value is 0
gpio: pin 55 (gpio 55) value is 0
gpio: pin 54 (gpio 54) value is 0
gpio: pin 53 (gpio 53) value is 1
switch to partitions #0, OK
mmc0 is current device
gpio: pin 54 (gpio 54) value is 1
Checking for: /uEnv.txt ...
Checking for: /boot.scr ...
Checking for: /boot/boot.scr ...
Checking for: /boot/uEnv.txt ...
gpio: pin 55 (gpio 55) value is 1
55 bytes read in 35 ms (1000 Bytes/s)
Loaded environment from /boot/uEnv.txt
Checking if uname_r is set in /boot/uEnv.txt...
gpio: pin 56 (gpio 56) value is 1
Running uname_boot ...
loading /boot/vmlinuz-5.9.0-rc7-bone4.1 ...
8991232 bytes read in 604 ms (14.2 MiB/s)
debug: [enable_uboot_overlays=] ...
loading /boot/dtbs/5.9.0-rc7-bone4.1/am335x-boneblack.dtb ...
87799 bytes read in 53 ms (1.6 MiB/s)
uboot_overlays: add [enable_uboot_overlays=1] to /boot/uEnv.txt to enable...
debug: [console=ttyO0,115200n8 root=/dev/mmcblk0p1 ro rootfstype=ext4
rootwait] ...
debug: [bootz 0x82000000 - 0x88000000] ...
## Flattened Device Tree blob at 88000000
Booting using the fdt blob at 0x88000000
Loading Device Tree to 8ffe7000, end 8ffff6f6 ... OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 5.9.0-rc7-bone4.1 (sleepy@seraph)
(arm-none-linux-gnueabihf-gcc (GNU Toolchain for the A-profile Architecture
9.2-2019.12 (arm-9.10)) 9.2.1 2019100
[ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7),
cr=50c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing
instruction cache
[ 0.000000] OF: fdt: Machine model: TI AM335x BeagleBone Black
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] efi: UEFI not found.
[ 0.000000] cma: Reserved 48 MiB at 0x9c800000
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000080000000-0x000000009fefffff]
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000080000000-0x000000009fefffff]
[ 0.000000] Initmem setup node 0 [mem
0x0000000080000000-0x000000009fefffff]
[ 0.000000] CPU: All CPU(s) started in SVC mode.
[ 0.000000] AM335X ES2.1 (sgx neon)
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129666
[ 0.000000] Kernel command line: console=ttyO0,115200n8
root=/dev/mmcblk0p1 ro rootfstype=ext4 rootwait
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144
bytes, linear)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072
bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 450244K/523264K available (9216K kernel code, 1200K
rwdata, 3592K rodata, 1024K init, 2896K bss, 23868K reserved, 49152K
cma-reserved, 0K highmem)
[ 0.000000] random: get_random_u32 called from
__kmem_cache_create+0x1d/0x230 with crng_init=0
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] ftrace: allocating 42810 entries in 84 pages
[ 0.000000] ftrace: allocated 84 pages with 3 groups
[ 0.000000] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000] Trampoline variant of Tasks RCU enabled.
[ 0.000000] Rude variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is
25 jiffies.
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] IRQ: Found an INTC at 0x(ptrval) (revision 5.0) with 128
interrupts
[ 0.000000] TI gptimer clocksource: always-on
/ocp/interconnect@44c00000/segment@200000/target-module@31000
[ 0.000009] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every
89478484971ns
[ 0.000026] clocksource: dmtimer: mask: 0xffffffff max_cycles:
0xffffffff, max_idle_ns: 79635851949 ns
[ 0.000514] TI gptimer clockevent: 24000000 Hz at
/ocp/interconnect@48000000/segment@0/target-module@40000
[ 0.001784] Console: colour dummy device 80x30
[ 0.001819] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0'
[ 0.001825] This ensures that you still see kernel messages. Please
[ 0.001831] update your kernel commandline.
[ 0.001899] Calibrating delay loop... 995.32 BogoMIPS (lpj=1990656)
[ 0.048549] pid_max: default: 32768 minimum: 301
[ 0.049380] LSM: Security Framework initializing
[ 0.049604] Yama: becoming mindful.
[ 0.050285] AppArmor: AppArmor initialized
[ 0.050317] TOMOYO Linux initialized
[ 0.050596] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes,
linear)
[ 0.050620] Mountpoint-cache hash table entries: 1024 (order: 0, 4096
bytes, linear)
[ 0.054380] CPU: Testing write buffer coherency: ok
[ 0.054541] CPU0: Spectre v2: using BPIALL workaround
[ 0.056619] Setting up static identity map for 0x80100000 - 0x80100054
[ 0.056947] rcu: Hierarchical SRCU implementation.
[ 0.060873] EFI services will not be available.
[ 0.062002] devtmpfs: initialized
[ 0.201100] VFP support v0.3: implementor 41 architecture 3 part 30
variant c rev 3
[ 0.203277] clocksource: jiffies: mask: 0xffffffff max_cycles:
0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.203319] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[ 0.207677] xor: automatically using best checksumming function neon
[ 0.207704] pinctrl core: initialized pinctrl subsystem
[ 0.212946] NET: Registered protocol family 16
[ 0.216235] DMA: preallocated 256 KiB pool for atomic coherent
allocations
[ 0.237165] l3-aon-clkctrl:0000:0: failed to disable
[ 0.240530] audit: initializing netlink subsys (disabled)
[ 0.244171] thermal_sys: Registered thermal governor 'fair_share'
[ 0.244178] thermal_sys: Registered thermal governor 'bang_bang'
[ 0.244195] thermal_sys: Registered thermal governor 'step_wise'
[ 0.244704] audit: type=2000 audit(0.232:1): state=initialized
audit_enabled=0 res=1
[ 0.244813] cpuidle: using governor menu
[ 1.032582] random: fast init done
[ 1.541322] hw-breakpoint: debug architecture 0x4 unsupported.
[ 1.615692] raid6: skip pq benchmark and using algorithm neonx8
[ 1.615713] raid6: using neon recovery algorithm
[ 1.622614] iommu: Default domain type: Translated
[ 1.627361] SCSI subsystem initialized
[ 1.628905] usbcore: registered new interface driver usbfs
[ 1.629180] usbcore: registered new interface driver hub
[ 1.629425] usbcore: registered new device driver usb
[ 1.631174] pps_core: LinuxPPS API ver. 1 registered
[ 1.631186] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo
Giometti <[email protected]>
[ 1.631280] PTP clock support registered
[ 1.633821] Advanced Linux Sound Architecture Driver Initialized.
[ 1.637345] NetLabel: Initializing
[ 1.637360] NetLabel: domain hash size = 128
[ 1.637367] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO
[ 1.637670] NetLabel: unlabeled traffic allowed by default
[ 1.639119] clocksource: Switched to clocksource dmtimer
[ 3.220973] VFS: Disk quotas dquot_6.6.0
[ 3.221147] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096
bytes)
[ 3.224729] AppArmor: AppArmor Filesystem Enabled
[ 3.269516] NET: Registered protocol family 2
[ 3.272071] tcp_listen_portaddr_hash hash table entries: 512 (order: 0,
4096 bytes, linear)
[ 3.272198] TCP established hash table entries: 4096 (order: 2, 16384
bytes, linear)
[ 3.272250] TCP bind hash table entries: 4096 (order: 2, 16384 bytes,
linear)
[ 3.272289] TCP: Hash tables configured (established 4096 bind 4096)
[ 3.272583] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 3.272626] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes,
linear)
[ 3.273433] NET: Registered protocol family 1
[ 3.275979] RPC: Registered named UNIX socket transport module.
[ 3.275997] RPC: Registered udp transport module.
[ 3.276004] RPC: Registered tcp transport module.
[ 3.276011] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 3.276028] NET: Registered protocol family 44
[ 3.277653] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5
counters available
[ 3.284662] Initialise system trusted keyrings
[ 3.285257] workingset: timestamp_bits=14 max_order=17 bucket_order=3
[ 3.326137] zbud: loaded
[ 3.340588] NFS: Registering the id_resolver key type
[ 3.340702] Key type id_resolver registered
[ 3.340710] Key type id_legacy registered
[ 3.341452] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 3.342234] fuse: init (API version 7.31)
[ 3.444026] Key type asymmetric registered
[ 3.444050] Asymmetric key parser 'x509' registered
[ 3.444269] Block layer SCSI generic (bsg) driver version 0.4 loaded
(major 246)
[ 3.444712] io scheduler mq-deadline registered
[ 3.621853] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed
to register, -517
[ 3.621883] omap_gpio 44e07000.gpio: Could not register gpio chip -517
[ 3.764638] ti-sysc: probe of 44e31000.target-module failed with error
-16
[ 3.806534] ti-sysc 4802a000.target-module: OCP softreset timed out
[ 3.823773] ti-sysc: probe of 48040000.target-module failed with error
-16
[ 3.912427] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed
to register, -517
[ 3.912458] omap_gpio 4804c000.gpio: Could not register gpio chip -517
[ 3.947348] omap-mailbox 480c8000.mailbox: omap mailbox rev 0x400
[ 3.992126] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed
to register, -517
[ 3.992157] omap_gpio 481ac000.gpio: Could not register gpio chip -517
[ 4.006595] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed
to register, -517
[ 4.006624] omap_gpio 481ae000.gpio: Could not register gpio chip -517
[ 4.062465] ti-sysc 4a101200.target-module: OCP softreset timed out
[ 4.072600] ti-sysc 4a101200.target-module: OCP softreset timed out
[ 4.140438] debugfs: Directory '49000000.dma' with parent 'dmaengine'
already present!
[ 4.140493] edma 49000000.dma: TI EDMA DMA engine driver
[ 4.183083] pinctrl-single 44e10800.pinmux: 142 pins, size 568
[ 4.225236] wkup_m3_ipc 44e11324.wkup_m3_ipc: could not get rproc handle
[ 4.228595] Serial: 8250/16550 driver, 6 ports, IRQ sharing disabled
[ 4.242059] 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 20,
base_baud = 3000000) is a 8250
[ 5.072967] printk: console [ttyS0] enabled
[ 5.084427] omap_rng 48310000.rng: Random Number Generator ver. 20
[ 5.091338] random: crng init done
[ 5.096975] sdhci: Secure Digital Host Controller Interface driver
[ 5.103319] sdhci: Copyright(c) Pierre Ossman
[ 5.108496] sdhci-pltfm: SDHCI platform and OF driver helper
[ 5.125055] sdhci-omap 481d8000.mmc: supply vqmmc not found, using dummy
regulator
[ 5.162780] mmc0: SDHCI controller on 481d8000.mmc [481d8000.mmc] using
External DMA
[ 5.191089] libphy: Fixed MDIO Bus: probed
[ 5.199699] CAN device driver interface
[ 5.215870] ti-sysc 4a101200.target-module: OCP softreset timed out
[ 5.242340] mmc0: new high speed MMC card at address 0001
[ 5.251694] mmcblk0: mmc0:0001 M62704 3.56 GiB
[ 5.258406] mmcblk0boot0: mmc0:0001 M62704 partition 1 2.00 MiB
[ 5.266465] mmcblk0boot1: mmc0:0001 M62704 partition 2 2.00 MiB
[ 5.272505] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6, bus
freq 1000000
[ 5.281054] mmcblk0rpmb: mmc0:0001 M62704 partition 3 512 KiB, chardev
(245:0)
[ 5.288415] libphy: 4a101000.mdio: probed
[ 5.301605] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00,
driver SMSC LAN8710/LAN8720
[ 5.311380] mmcblk0: p1
[ 5.324386] cpsw 4a100000.ethernet: initialized cpsw ale version 1.4
[ 5.338928] cpsw 4a100000.ethernet: ALE Table size 1024
[ 5.347635] cpsw 4a100000.ethernet: cpts: overflow check period 1250
(jiffies)
[ 5.356390] cpsw 4a100000.ethernet: Detected MACID = 64:cf:d9:45:3f:41
[ 5.369526] usbcore: registered new interface driver smsc95xx
[ 5.378185] am335x-phy-driver 47401300.usb-phy: supply vcc not found,
using dummy regulator
[ 5.396756] am335x-phy-driver 47401b00.usb-phy: supply vcc not found,
using dummy regulator
[ 5.412728] usbcore: registered new interface driver uas
[ 5.418615] usbcore: registered new interface driver usb-storage
[ 5.424932] usbcore: registered new interface driver ums-alauda
[ 5.431081] usbcore: registered new interface driver ums-cypress
[ 5.437295] usbcore: registered new interface driver ums-datafab
[ 5.443508] usbcore: registered new interface driver ums_eneub6250
[ 5.449885] usbcore: registered new interface driver ums-freecom
[ 5.456094] usbcore: registered new interface driver ums-isd200
[ 5.462209] usbcore: registered new interface driver ums-jumpshot
[ 5.468500] usbcore: registered new interface driver ums-karma
[ 5.474524] usbcore: registered new interface driver ums-onetouch
[ 5.480908] usbcore: registered new interface driver ums-realtek
[ 5.487161] usbcore: registered new interface driver ums-sddr09
[ 5.493268] usbcore: registered new interface driver ums-sddr55
[ 5.499394] usbcore: registered new interface driver ums-usbat
[ 5.516021] musb-hdrc musb-hdrc.1: MUSB HDRC host driver
[ 5.521602] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus
number 1
[ 5.530042] usb usb1: New USB device found, idVendor=1d6b,
idProduct=0002, bcdDevice= 5.09
[ 5.538425] usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 5.545724] usb usb1: Product: MUSB HDRC host driver
[ 5.550774] usb usb1: Manufacturer: Linux 5.9.0-rc7-bone4.1 musb-hcd
[ 5.557177] usb usb1: SerialNumber: musb-hdrc.1
[ 5.564620] hub 1-0:1.0: USB hub found
[ 5.568652] hub 1-0:1.0: 1 port detected
[ 5.581989] dummy_hcd dummy_hcd.0: USB Host+Gadget Emulator, driver 02
May 2005
[ 5.589633] dummy_hcd dummy_hcd.0: Dummy host controller
[ 5.595042] dummy_hcd dummy_hcd.0: new USB bus registered, assigned bus
number 2
[ 5.603708] usb usb2: New USB device found, idVendor=1d6b,
idProduct=0002, bcdDevice= 5.09
[ 5.612077] usb usb2: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 5.619379] usb usb2: Product: Dummy host controller
[ 5.624427] usb usb2: Manufacturer: Linux 5.9.0-rc7-bone4.1 dummy_hcd
[ 5.630931] usb usb2: SerialNumber: dummy_hcd.0
[ 5.638262] hub 2-0:1.0: USB hub found
[ 5.642297] hub 2-0:1.0: 1 port detected
[ 5.660029] omap_rtc 44e3e000.rtc: registered as rtc0
[ 5.665282] omap_rtc 44e3e000.rtc: setting system clock to
2000-01-01T00:00:00 UTC (946684800)
[ 5.677772] i2c /dev entries driver
[ 5.687104] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60
sec
[ 5.695656] softdog: initialized. soft_noboot=0 soft_margin=60 sec
soft_panic=0 (nowayout=0)
[ 5.704215] softdog: soft_reboot_cmd=<not set>
soft_active_on_boot=0
[ 5.714748] cpuidle: enable-method property 'ti,am3352' found operations
[ 5.724729] ledtrig-cpu: registered to indicate activity on CPUs
[ 5.732324] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2
[ 5.738872] omap-aes 53500000.aes: will run requests pump with realtime
priority
[ 5.750790] omap-sham 53100000.sham: hw accel on OMAP rev 4.3
[ 5.764975] hid: raw HID events driver (C) Jiri Kosina
[ 5.772041] usbcore: registered new interface driver usbhid
[ 5.777779] usbhid: USB HID core driver
[ 5.782905] remoteproc remoteproc0: wkup_m3 is available
[ 5.796610] drop_monitor: Initializing network drop monitor service
[ 5.806982] NET: Registered protocol family 10
[ 5.820793] Segment Routing with IPv6
[ 5.824992] mip6: Mobile IPv6
[ 5.828414] NET: Registered protocol family 17
[ 5.833124] can: controller area network core (rev 20170425 abi 9)
[ 5.839766] NET: Registered protocol family 29
[ 5.845094] Key type dns_resolver registered
[ 5.849491] mpls_gso: MPLS GSO support
[ 5.853465] ThumbEE CPU extension supported.
[ 5.857852] Registering SWP/SWPB emulation handler
[ 5.862691] omap_voltage_late_init: Voltage driver support not added
[ 5.869836] PM: Cannot get wkup_m3_ipc handle
[ 5.875636] registered taskstats version 1
[ 5.879912] Loading compiled-in X.509 certificates
[ 5.885054] zswap: loaded using pool lzo/zbud
[ 5.890647] kmemleak: Kernel memory leak detector initialized (mem pool
available: 15836)
[ 5.898951] kmemleak: Automatic memory scanning thread started
[ 5.905738] Key type ._fscrypt registered
[ 5.909884] Key type .fscrypt registered
[ 5.913871] Key type fscrypt-provisioning registered
[ 5.928657] Btrfs loaded, crc32c=crc32c-generic
[ 5.933609] AppArmor: AppArmor sha1 policy hashing enabled
[ 6.007537] OMAP GPIO hardware version 0.1
[ 6.040147] tps65217-pmic: Failed to locate of_node [id: -1]
[ 6.060720] tps65217-bl: Failed to locate of_node [id: -1]
[ 6.070926] tps6521x_pwrbutton tps65217-pwrbutton: DMA mask not set
[ 6.079912] input: tps65217_pwr_but as
/devices/platform/ocp/44c00000.interconnect/44c00000.interconnect:segment@200000/44e0b000.target-module/44e0b000.i2c/i2c-0/0-0024/tps0
[ 6.098523] tps65217 0-0024: TPS65217 ID 0xe version 1.2
[ 6.105104] at24 0-0050: supply vcc not found, using dummy regulator
[ 6.113487] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1
bytes/write
[ 6.123354] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz
[ 6.136637] at24 2-0054: supply vcc not found, using dummy regulator
[ 6.175689] at24 2-0055: supply vcc not found, using dummy regulator
[ 6.214521] at24 2-0056: supply vcc not found, using dummy regulator
[ 6.250526] at24 2-0057: supply vcc not found, using dummy regulator
[ 6.286453] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz
[ 6.303725] omap_gpio 44e07000.gpio: Could not set line 6 debounce to
200000 microseconds (-22)
[ 6.312645] remoteproc remoteproc0: powering up wkup_m3
[ 6.317977] remoteproc remoteproc0: Booting fw image
am335x-pm-firmware.elf, size 217168
[ 6.326157] sdhci-omap 48060000.mmc: Got CD GPIO
[ 6.331160] wkup_m3_ipc 44e11324.wkup_m3_ipc: CM3 Firmware Version =
0x193
[ 6.338516] sdhci-omap 48060000.mmc: supply vqmmc not found, using dummy
regulator
[ 6.346206] remoteproc remoteproc0: remote processor wkup_m3 is now up
[ 6.383929] mmc1: SDHCI controller on 48060000.mmc [48060000.mmc] using
External DMA
[ 6.420410] PM: bootloader does not support rtc-only!
[ 6.457532] mmc1: new high speed SDXC card at address aaaa
[ 6.466835] mmcblk1: mmc1:aaaa SN64G 59.5 GiB
[ 6.478915] mmcblk1: p1
[ 6.549949] tda998x 0-0070: found TDA19988
[ 6.561079] tilcdc 4830e000.lcdc: bound 0-0070 (ops 0xc0a8a5dc)
[ 6.570416] [drm] Initialized tilcdc 1.0.0 20121205 for 4830e000.lcdc on
minor 0
[ 6.578589] tilcdc 4830e000.lcdc: [drm] Cannot find any crtc or sizes
[ 6.590416] ALSA device list:
[ 6.593930] No soundcards found.
[ 6.597629] tilcdc 4830e000.lcdc: [drm] Cannot find any crtc or sizes
[ 6.616256] EXT4-fs (mmcblk0p1): INFO: recovery required on readonly
filesystem
[ 6.623687] EXT4-fs (mmcblk0p1): write access will be enabled during
recovery
[ 6.800548] EXT4-fs (mmcblk0p1): recovery complete
[ 6.807002] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data
mode. Opts: (null)
[ 6.815503] VFS: Mounted root (ext4 filesystem) readonly on device 179:1.
[ 6.828643] devtmpfs: mounted
[ 6.849288] Freeing unused kernel memory: 1024K
[ 6.860280] Run /sbin/init as init process
[ 6.883685] Not activating Mandatory Access Control as /sbin/tomoyo-init
does not exist.
[ 7.175450] systemd[1]: System time before build time, advancing clock.
[ 7.244222] systemd[1]: systemd 232 running in system mode. (+PAM +AUDIT
+SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT
+GNUTLS +ACL +XZ +LZ4 +SECCOM)
[ 7.264002] systemd[1]: Detected architecture arm.
I compiled the kernel (bb-kernel) on my desktop and copied the kernel,
dtbs, and modules to /boot on the SD card following this guide:
https://www.digikey.com/eewiki/display/linuxonarm/BeagleBone+Black
I've read through the log but I'm not really sure what's going on here.
How can I fix this?
Best,
Brooke Basile
--
For more options, visit http://beagleboard.org/discuss
---
You received this message because you are subscribed to the Google Groups
"BeagleBoard" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to [email protected].
To view this discussion on the web visit
https://groups.google.com/d/msgid/beagleboard/55f9501f-fdc9-46ca-acde-8e1de991b84an%40googlegroups.com.
