On Thursday, September 6, 2018 at 5:48:39 PM UTC-4, [email protected] wrote:
> > Just for sanity I will rebuild the rcn-ee_console_debian_stretch_armhf but > with a flasher and retry that. > I rebuilt from scratch and generated an eMMC flasher, installed and I get the same results as with USB mass-storage flashing. I noticed that the fast-blink of the green LED starts almost at power up, which is odd and makes me think it's a u-boot or dtb issue? Here's the compete output from power up to login prompt: U-Boot SPL 2018.03-00002-gac9cce7c6a (Apr 05 2018 - 13:07:46 -0500) Trying to boot from MMC2 Loading Environment from EXT4... Card did not respond to voltage select! ** Bad device mmc 0 ** Failed (-5) U-Boot 2018.03-00002-gac9cce7c6a (Apr 05 2018 - 13:07:46 -0500), Build: jenkins-github_Bootloader-Builder-47 CPU : AM335X-GP rev 2.1 I2C: ready DRAM: 512 MiB No match for driver 'omap_hsmmc' No match for driver 'omap_hsmmc' Some drivers were not found Reset Source: Power-on reset has occurred. RTC 32KCLK Source: External. MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Loading Environment from EXT4... Card did not respond to voltage select! ** Bad device mmc 0 ** Failed (-5) Board: BeagleBone Black <ethaddr> not set. Validating first E-fuse MAC BeagleBone Black: BeagleBone: cape eeprom: i2c_probe: 0x54: BeagleBone: cape eeprom: i2c_probe: 0x55: BeagleBone: cape eeprom: i2c_probe: 0x56: BeagleBone: cape eeprom: i2c_probe: 0x57: Net: eth0: MII MODE cpsw, usb_ether Press SPACE to abort autoboot in 2 seconds board_name=[A335BNLT] ... board_rev=[00C0] ... Card did not respond to voltage select! Card did not respond to voltage select! Card did not respond to voltage select! gpio: pin 56 (gpio 56) value is 0 gpio: pin 55 (gpio 55) value is 0 gpio: pin 54 (gpio 54) value is 0 gpio: pin 53 (gpio 53) value is 1 Card did not respond to voltage select! Card did not respond to voltage select! switch to partitions #0, OK mmc1(part 0) is current device Scanning mmc 1:1... gpio: pin 56 (gpio 56) value is 0 gpio: pin 55 (gpio 55) value is 0 gpio: pin 54 (gpio 54) value is 0 gpio: pin 53 (gpio 53) value is 1 switch to partitions #0, OK mmc1(part 0) is current device gpio: pin 54 (gpio 54) value is 1 Checking for: /uEnv.txt ... Checking for: /boot.scr ... Checking for: /boot/boot.scr ... Checking for: /boot/uEnv.txt ... gpio: pin 55 (gpio 55) value is 1 2102 bytes read in 32 ms (63.5 KiB/s) Loaded environment from /boot/uEnv.txt Checking if uname_r is set in /boot/uEnv.txt... gpio: pin 56 (gpio 56) value is 1 Running uname_boot ... loading /boot/vmlinuz-4.14.67-ti-r73 ... 10379776 bytes read in 679 ms (14.6 MiB/s) loading /boot/dtbs/4.14.67-ti-r73/am335x-boneblack.dtb ... 60317 bytes read in 61 ms (964.8 KiB/s) uboot_overlays: add [enable_uboot_overlays=1] to /boot/uEnv.txt to enable... loading /boot/initrd.img-4.14.67-ti-r73 ... 4530206 bytes read in 315 ms (13.7 MiB/s) debug: [console=ttyO0,115200n8 root=/dev/mmcblk1p1 ro rootfstype=btrfs rootwait coherent_pool=1M net.ifnames=0 quiet] ... debug: [bootz 0x82000000 0x88080000:45201e 0x88000000] ... ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Loading Ramdisk to 8fbad000, end 8ffff01e ... OK Loading Device Tree to 8fb9b000, end 8fbacb9c ... OK Starting kernel ... [ 0.000760] timer_probe: no matching timers found [ 0.542293] dmi: Firmware registration failed. [ 1.036826] wkup_m3_ipc 44e11324.wkup_m3_ipc: could not get rproc handle [ 1.253210] dmi-sysfs: dmi entry is absent. [ 1.285511] omap_voltage_late_init: Voltage driver support not added [ 1.595720] hdmi-audio-codec hdmi-audio-codec.0.auto: ASoC: no source widget found for Playback [ 1.604591] hdmi-audio-codec hdmi-audio-codec.0.auto: ASoC: Failed to add route Playback -> direct -> TX Debian GNU/Linux 9 arm ttyS0 rcn-ee.net console Debian Image 2018-09-06 Support/FAQ: http://elinux.org/BeagleBoardDebian default username:password is [debian:temppwd] arm login: Next up, I'll retry without btrfs (i.e. omitting the --rootfs btrfs on the sdcard_setup step). Thanks! -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/beagleboard/d1f33255-1170-4449-b219-863609c60c00%40googlegroups.com. For more options, visit https://groups.google.com/d/optout.
