I get the same problem in the end, but it tries a few other things first:
https://pastebin.com/bZJ26b7A
• Gave up waiting for root file system device. Common problems:
• - Boot args (cat /proc/cmdline)
• - Check rootdelay= (did the system wait long enough?)
• - Missing modules (cat /proc/modules; ls /dev)
• ALERT! /dev/mmcblk0p1 does not exist. Dropping to a shell!
I put the output of `cat /proc/cmdline` and `cat /proc/modules; ls /dev` in the
paste, as well.
> On Feb 16, 2018, at 07:50 , [email protected] wrote:
>
> Hi,
> I had the same problem with a current
> bbx15-debian-9.3-iot-armhf-2018-02-11-4gb.img.xz Image.
> Flashing the SD Card to the onboard eMMC works for me (uncomment the last
> line at /boot/uEnv.txt on the SD Card file system + boot again with SD Card
> inserted).
>
> Joerg
>
> On Saturday, February 10, 2018 at 1:31:27 AM UTC+1, Rick M wrote:
> I downloaded the stretch-console for x15 and imaged an 8GB SD Card on macOS
> using Etcher. I put this in the x15 and powered it on. It gets partway
> through the boot process, and appears to be booting from the SD card (the
> installed kernel on the MMC is -r44, and the log shows -r96), but then it
> gets stuck. There's a fairly long delay after "mmc0: error -110 whilst
> initialising SD card." Console log below:
>
> https://pastebin.com/Y5pX3uBW
>
>
> �
> U-Boot SPL 2017.01-00360-gc604741cb3 (Aug 11 2017 - 15:47:09)
> DRA752-GP ES2.0
> Trying to boot from MMC1
>
> ** Unable to use mmc 0:1 for loading the env **
> Using default environment
>
>
>
> U-Boot 2017.01-00360-gc604741cb3 (Aug 11 2017 - 15:47:09 -0500), Build:
> jenkins-github_Bootloader-Builder-592
>
> CPU : DRA752-GP ES2.0
> Model: TI AM5728 BeagleBoard-X15
> Board: BeagleBoard X15 REV C.00
> DRAM: 2 GiB
> MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1
>
> ** Unable to use mmc 0:1 for loading the env **
> Using default environment
>
> setup_board_eeprom_env: beagle_x15_revc
> SCSI: SATA link 0 timeout.
> AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
> flags: 64bit ncq stag pm led clo only pmp pio slum part ccc apst
> scanning bus for devices...
> Found 0 device(s).
> Net: <ethaddr> not set. Validating first E-fuse MAC
> cpsw
> Press SPACE to abort autoboot in 2 seconds
> usb_boot is currently disabled
> scsi_boot is currently disabled
> switch to partitions #0, OK
> mmc0 is current device
> Scanning mmc device 0
> Checking for: /uEnv.txt ...
> Checking for: /boot/uEnv.txt ...
> 445 bytes read in 29 ms (14.6 KiB/s)
> Loaded environment from /boot/uEnv.txt
> Checking if uname_r is set in /boot/uEnv.txt ...
> debug: [uname_r=4.9.79-ti-r96] ...
> loading /boot/vmlinuz-4.9.79-ti-r96 ...
> 9961120 bytes read in 461 ms (20.6 MiB/s)
> loading /boot/dtbs/4.9.79-ti-r96/am57xx-beagle-x15-revc.dtb ...
> 153258 bytes read in 84 ms (1.7 MiB/s)
> loading /boot/initrd.img-4.9.79-ti-r96 ...
> 5756938 bytes read in 281 ms (19.5 MiB/s)
> debug: [console=ttyO2,115200n8 root=/dev/mmcblk0p1 ro rootfstype=ext4
> rootwait coherent_pool=1M net.ifnames=0 quiet] ...
> debug: [bootz 0x82000000 0x88080000:57d80a 0x88000000] ...
> ## Flattened Device Tree blob at 88000000
> Booting using the fdt blob at 0x88000000
> Loading Ramdisk to 8fa82000, end 8ffff80a ... OK
> Loading Device Tree to 8fa59000, end 8fa816a9 ... OK
>
> Starting kernel ...
>
> [ 0.074308] /cpus/cpu@0 missing clock-frequency property
> [ 0.074332] /cpus/cpu@1 missing clock-frequency property
> [ 2.410682] dra7-pcie 51000000.pcie: phy link never came up
> [ 2.671093] omap_hsmmc 480b4000.mmc: no pinctrl state for sdr25 mode
> [ 2.686786] omap_hsmmc 480b4000.mmc: no pinctrl state for sdr12 mode
> [ 2.759464] omap_voltage_late_init: Voltage driver support not added
> [ 3.760897] omap_hsmmc 4809c000.mmc: card busy
> [ 3.810275] mmc0: error -110 whilst initialising SD card
> Gave up waiting for root file system device. Common problems:
> - Boot args (cat /proc/cmdline)
> - Check rootdelay= (did the system wait long enough?)
> - Missing modules (cat /proc/modules; ls /dev)
> ALERT! /dev/mmcblk0p1 does not exist. Dropping to a shell!
> (initramfs)
>
>
> --
> Rick Mann
> [email protected]
>
>
>
> --
> For more options, visit http://beagleboard.org/discuss
> ---
> You received this message because you are subscribed to the Google Groups
> "BeagleBoard" group.
> To unsubscribe from this group and stop receiving emails from it, send an
> email to [email protected].
> To view this discussion on the web visit
> https://groups.google.com/d/msgid/beagleboard/e3dfb1a8-5bf4-4362-ba73-53fa3363b2ef%40googlegroups.com.
> For more options, visit https://groups.google.com/d/optout.
--
Rick Mann
[email protected]
--
For more options, visit http://beagleboard.org/discuss
---
You received this message because you are subscribed to the Google Groups
"BeagleBoard" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to [email protected].
To view this discussion on the web visit
https://groups.google.com/d/msgid/beagleboard/80B24352-2665-47DB-92CC-8502E8C63BF3%40latencyzero.com.
For more options, visit https://groups.google.com/d/optout.
