I've tried that and it doesn't work. Here's what I get: U-Boot SPL 2013.04-dirty (Jul 10 2013 - 14:02:53) musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Peripheral mode controller at 47401000 using PIO, IRQ 0 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Host mode controller at 47401800 using PIO, IRQ 0 OMAP SD/MMC: 0 mmc_send_cmd : timeout: No status update reading u-boot.img reading u-boot.img
U-Boot 2013.04-dirty (Jul 10 2013 - 14:02:53) I2C: ready DRAM: 512 MiB WARNING: Caches not enabled NAND: No NAND device found!!! 0 MiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 *** Warning - readenv() failed, using default environment musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Peripheral mode controller at 47401000 using PIO, IRQ 0 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Host mode controller at 47401800 using PIO, IRQ 0 Net: <ethaddr> not set. Validating first E-fuse MAC cpsw, usb_ether Hit any key to stop autoboot: 0 gpio: pin 53 (gpio 53) value is 1 mmc0 is current device micro SD card found mmc0 is current device gpio: pin 54 (gpio 54) value is 1 SD/MMC found on device 0 ** File not found uEnv.txt ** gpio: pin 55 (gpio 55) value is 1 ** Invalid partition 2 ** On Thursday, October 26, 2017 at 11:25:01 AM UTC-4, RobertCNelson wrote: > > On Thu, Oct 26, 2017 at 10:22 AM, Mark A. Yoder <[email protected] > <javascript:>> wrote: > > I've dug up and old BeagleBone Black A6 that has Angstrom on the eMMC. > It > > won't boot off an SD with a current image (** Invalid partition 2 **). > > > > How do I update it to run a current image? > > Hold the "boot" button, insert power. ;) > > Regards, > > -- > Robert Nelson > https://rcn-ee.com/ > -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/beagleboard/7003f7c2-6964-4a7a-946b-fcb5f23e4e62%40googlegroups.com. For more options, visit https://groups.google.com/d/optout.
