HI Robert,
One more thing, I did printenv and checked the loadaddress ( there are 3
addresses kloadaddr, loadaddr and rdaddr which one should I consider ) and
device tree address, which address I should consider( you mentioned address
or my addresses which I see in printenv)?. can you please see below log
which I have highlighted in red color.
arch=arm
baudrate=115200
board=am335x
board_name=A335BNLT
board_rev=00C0
bootcmd=gpio set 53; i2c mw 0x24 1 0x3e; run findfdt; mmc dev 0; if mmc
rescan ; then echo micro SD card found;setenv mmcdev 0;else echo No micro
SD card found, setting mmcdev to 1;setenv mmcdev 1;fi;setenv bootpart
${mmcdev}:2;mmc dev ${mmcdev}; if mmc rescan; then gpio set 54; echo SD/MMC
found on device ${mmcdev};if run loadbootenv; then echo Loaded environment
from ${bootenv};run importbootenv;fi;if test -n $uenvcmd; then echo Running
uenvcmd ...;run uenvcmd;fi;gpio set 55; if run loaduimage; then gpio set
56; run loadfdt;run mmcboot;fi;fi;
bootdelay=1
bootdir=/boot
bootenv=uEnv.txt
bootfile=uImage
bootpart=0:2
console=ttyO0,115200n8
cpu=armv7
fdt_high=0xffffffff
*fdtaddr=0x80F80000*
fdtfile=am335x-boneblack.dtb
ipaddr=192.168.0.100
*kloadaddr=0x80007fc0*
*loadaddr=0x80200000*
nandimgsize=0x500000
nandroot=ubi0:rootfs rw ubi.mtd=7,2048
nandrootfstype=ubifs rootwait=1
nandsrcaddr=0x280000
ramrootfstype=ext2
*rdaddr=0x81000000*
rootpath=/export/rootfs
serverip=192.168.0.1
soc=am33xx
Please help me.
Thanks and regards,
Madhu
On Wednesday, December 21, 2016 at 11:04:14 AM UTC+5:30, Madhu K wrote:
>
> Hi Robert,
>
> Thank you so for your response.
>
> I have small doubt.In below mentioned addresses which is kernel load
> address and which is dtb( device tree) loadaddress?
>
> loadaddr=0x82000000
> rdaddr=0x88080000
>
> Thanks and regards,
> Madhu
>
> On Tuesday, December 20, 2016 at 8:52:35 PM UTC+5:30, RobertCNelson wrote:
>>
>> On Mon, Dec 19, 2016 at 11:56 PM, Madhu K <[email protected]> wrote:
>> > Hi All,
>> >
>> >
>> > I am newbie in Linux and BBB , I am sure this topic might have come
>> multiple
>> > times in this forum but unfortunately those could not resolve my issue
>> .
>> >
>> > I am facing u-boot stuck at "Starting Kernel" message, there after no
>> > messages in u-boot prompt.
>> >
>> > I followed below steps.
>> >
>> > 1) tftp 0x80007fc0 uImage
>> > 2)tftp 0x80F80000 am335x-boneblack.dtb
>> > 3) bootm 0x80007fc0 - 0x80F80000.
>>
>> Use:
>>
>> loadaddr=0x82000000
>> rdaddr=0x88080000
>>
>> Regards,
>>
>> --
>> Robert Nelson
>> https://rcn-ee.com/
>>
>
--
For more options, visit http://beagleboard.org/discuss
---
You received this message because you are subscribed to the Google Groups
"BeagleBoard" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to [email protected].
To view this discussion on the web visit
https://groups.google.com/d/msgid/beagleboard/e5132384-cfc3-42d1-a7ee-d91f0900bcbc%40googlegroups.com.
For more options, visit https://groups.google.com/d/optout.
