Hi
Thank you so much for your response.
from where did you find the fdtaddr and loadaddr?
I did printenv in u-boot and captured a log, in that log i can see
different fdtaddr and loadaddr. which addresses should I use now, your
addresses or my addresses( which are highlighted in red color)?.
arch=arm
baudrate=115200
board=am335x
board_name=A335BNLT
board_rev=00C0
bootcmd=gpio set 53; i2c mw 0x24 1 0x3e; run findfdt; mmc dev 0; if mmc
rescan ; then echo micro SD card found;setenv mmcdev 0;else echo No micro
SD card found, setting mmcdev to 1;setenv mmcdev 1;fi;setenv bootpart
${mmcdev}:2;mmc dev ${mmcdev}; if mmc rescan; then gpio set 54; echo SD/MMC
found on device ${mmcdev};if run loadbootenv; then echo Loaded environment
from ${bootenv};run importbootenv;fi;if test -n $uenvcmd; then echo Running
uenvcmd ...;run uenvcmd;fi;gpio set 55; if run loaduimage; then gpio set
56; run loadfdt;run mmcboot;fi;fi;
bootdelay=1
bootdir=/boot
bootenv=uEnv.txt
bootfile=uImage
bootpart=0:2
console=ttyO0,115200n8
cpu=armv7
fdt_high=0xffffffff
*fdtaddr=0x80F80000*
fdtfile=am335x-boneblack.dtb
ipaddr=192.168.0.100
*kloadaddr=0x80007fc0*
*loadaddr=0x80200000*
nandimgsize=0x500000
nandroot=ubi0:rootfs rw ubi.mtd=7,2048
nandrootfstype=ubifs rootwait=1
nandsrcaddr=0x280000
ramrootfstype=ext2
*rdaddr=0x81000000*
rootpath=/export/rootfs
serverip=192.168.0.1
soc=am33xx
Please help me.
Thanks and regards,
Madhu
On Tuesday, December 20, 2016 at 8:08:34 PM UTC+5:30, J Evans wrote:
>
> Hello,
>
>
>
> With a 4.8 mainline kernel zImage I use
>
>
>
> fdtaddr=0x88000000
>
> loadaddr=0x82000000
>
>
>
> HTH
>
>
>
> *From:* [email protected] <javascript:> [mailto:
> [email protected] <javascript:>] *On Behalf Of *Madhu K
> *Sent:* 20 December 2016 06:23
> *To:* BeagleBoard
> *Cc:* Madhu babu
> *Subject:* [beagleboard] Load address for beagle bone.
>
>
>
> HI All,
>
>
>
> What is the Kernel and device tree load address for beaglebone black board.
>
>
>
> Thanks & regards,
>
> Madhu
>
> --
> For more options, visit http://beagleboard.org/discuss
> ---
> You received this message because you are subscribed to the Google Groups
> "BeagleBoard" group.
> To unsubscribe from this group and stop receiving emails from it, send an
> email to [email protected] <javascript:>.
> To view this discussion on the web visit
> https://groups.google.com/d/msgid/beagleboard/f6d05fae-4d52-4c86-b2d7-391f65ba9886%40googlegroups.com
>
> <https://groups.google.com/d/msgid/beagleboard/f6d05fae-4d52-4c86-b2d7-391f65ba9886%40googlegroups.com?utm_medium=email&utm_source=footer>
> .
> For more options, visit https://groups.google.com/d/optout.
>
--
For more options, visit http://beagleboard.org/discuss
---
You received this message because you are subscribed to the Google Groups
"BeagleBoard" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to [email protected].
To view this discussion on the web visit
https://groups.google.com/d/msgid/beagleboard/9102606c-a0b0-442f-8a87-213d399b5658%40googlegroups.com.
For more options, visit https://groups.google.com/d/optout.
