Prashant,
Could you please paste the entire config you're using? It would appear
that the "Storage" parameter can not be located in the job or job
defaults or schedule, leaving bacula with no possible destination for
one Run.
Regards,
Laurent Chouinard
On 2010-07-09 10:13, Prashant Ramhit wrote:
Hi Laurent,
Sorry, I've corrected the spelling mistakes, but there is still an
issue, as error says *Config error: Job type field: Storage in run
record not found*.
I think is it more of an invalid parameter in the schedule section.
I'll keep trying.
Regards,
Prashant
On 09/07/10 14:14, Laurent Chouinard wrote:
Prashant,
It almost sounds like a misspelling. I see that in your schedule, you
wrote LTO with a zero, like LT zero-two. But LTO drives have that
name for the acronym "Linear Tape Open", so if your storage config
spells it with the letterO, then that's a problem. Try copy-pasting
the name to be sure it's found.
Regards,
Laurent Chouinard
On 2010-07-09 09:02, Prashant Ramhit wrote:
Hi Laurent,
This is what it says when I restart bacula, after adding Storage=
LT02-Drive
r...@backupserver:/etc/bacula# /etc/init.d/bacula-director restart
* Stopping Bacula
Director...
[ OK ]
* Starting Bacula
Director...
09-Jul 13:56 bacula-dir: ERROR TERMINATION at run_conf.c:380
Config error: Job type field: Storage in run record not found
: line 10, col 45 of file /etc/bacula/schedules.conf
Run = Differential mon-thu at 23:45 Storage = LT02-Drive
Config:
Schedule {
Name = "WeeklyOffsite"
Run = Full sun at 3:00
Run = Differential mon-thu at 23:45 Storage = LT02-Drive
}
>From that, I assume that the parameters for specifying another
storage should be elsewhere,
Regards,
Prashant
On 09/07/10 13:40, Laurent Chouinard wrote:
On 2010-07-09 06:31, Prashant Ramhit wrote:
Hi All,
I have an LTO4 and LTO2 tapes drive on bacula.
How can I specify a Job/specify to use the LTO4 for full backup on
week ends and then differential for LTO2 mon-fri.
As the following does not work
Schedule {
Name = "WeeklyOffsite"
Run = Full sun at 3:00 Storage = LT04-drive
Run = Differential mon-thu at 23:45 Storage = LT02-drive
}
If you have the same setup could you please point me to the
correct documentation for this please.
Kind Regards,
Prashant Ramhit
Prashant,
What does the log say when it runs those jbos?
Which is the two fail? The full on LTO4, or the Diff on LTO2?
Also, if you run the job manually with "run" command, and then set
the type to "Full" and storage to "LTO4", (and then the same for
Diff/LTO2), can these jobs work fine?
Regards,
Laurent Chouinard
------------------------------------------------------------------------------
This SF.net email is sponsored by Sprint
What will you do first with EVO, the first 4G phone?
Visit sprint.com/first --http://p.sf.net/sfu/sprint-com-first
_______________________________________________
Bacula-users mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/bacula-users
------------------------------------------------------------------------------
This SF.net email is sponsored by Sprint
What will you do first with EVO, the first 4G phone?
Visit sprint.com/first -- http://p.sf.net/sfu/sprint-com-first
_______________________________________________
Bacula-users mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/bacula-users
