Bacula 2.2.6 on RHEL5 (2.6.18-53.1.4.el5xen)
# cat /proc/scsi/scsi
Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: 3ware Model: Logical Disk 0 Rev: 1.2
Type: Direct-Access ANSI SCSI revision: ffffffff
Host: scsi1 Channel: 00 Id: 00 Lun: 00
Vendor: 3ware Model: Logical Disk 0 Rev: 1.2
Type: Direct-Access ANSI SCSI revision: ffffffff
Host: scsi2 Channel: 00 Id: 00 Lun: 00
Vendor: QUALSTAR Model: RLS-8204-20 Rev: 006D
Type: Medium Changer ANSI SCSI revision: 02
Host: scsi2 Channel: 00 Id: 01 Lun: 00
Vendor: IBM Model: ULTRIUM-TD3 Rev: 73P5
Type: Sequential-Access ANSI SCSI revision: 03
Snippet from bacula-sd.conf:
>>>
Autochanger {
Name = Autochanger
Device = Drive-1
#Device = Drive-2
Changer Command = "/usr/local/bacula-2.2.6/scripts/mtx-changer %c %o
%S %a %d"
Changer Device = /dev/sg0
}
Device {
Name = Drive-1 #
Drive Index = 0
Media Type = DLT-8000
Archive Device = /dev/nst0
AutomaticMount = yes; # when device opened, read it
AlwaysOpen = yes;
RemovableMedia = yes;
RandomAccess = no;
AutoChanger = yes
#
# Enable the Alert command only if you have the mtx package loaded
# Note, apparently on some systems, tapeinfo resets the SCSI
controller
# thus if you turn this on, make sure it does not reset your SCSI
# controller. I have never had any problems, and smartctl does
# not seem to cause such problems.
#
Alert Command = "sh -c 'tapeinfo -f %c |grep TapeAlert|cat'"
#If you have smartctl, enable this, it has more info than tapeinfo
#Alert Command = "sh -c 'smartctl -H -l error %c'"
}
>>>
# ./btape -c ../etc/bacula-sd.conf /dev/nst0
Tape block granularity is 1024 bytes.
btape: butil.c:285 Using device: "/dev/nst0" for writing.
17-Dec 11:45 btape JobId 0: 3301 Issuing autochanger "loaded? drive 0"
command.
17-Dec 11:45 btape JobId 0: 3991 Bad autochanger "loaded? drive 0"
command: ERR=Child exited with code 1.
Results=mtx: Request Sense: Long Report=yes
mtx: Request Sense: Valid Residual=no
mtx: Request Sense: Error Code=0 (Unknown?!)
mtx: Request Sense: Sense Key=No Sense
mtx: Request Sense: FileMark=no
mtx: Request Sense: EOM=no
mtx: Request Sense: ILI=no
mtx: Request Sense: Additional Sense Code = 00
mtx: Request Sense: Additional Sense Qualifier = 00
mtx: Request Sense: BPV=no
mtx: Request Sense: Error in CDB=no
mtx: Request Sense: SKSV=no
READ ELEMENT STATUS Command Failed
17-Dec 11:45 btape: Fatal Error at device.c:296 because:
dev open failed: dev.c:433 Unable to open device "Drive-1" (/dev/nst0):
ERR=Input/output error
17-Dec 11:45 btape JobId 0: Fatal error: butil.c:194 Cannot open
"Drive-1" (/dev/nst0)
----------------------------------------
Robin P. Blanchard
Systems Administrator
Information Technology Outreach Services
Carl Vinson Institute of Government
The University of Georgia
fon 706.542.6295 // fax 706.542.6535
----------------------------------------
-------------------------------------------------------------------------
This SF.net email is sponsored by: Microsoft
Defy all challenges. Microsoft(R) Visual Studio 2008.
http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/
_______________________________________________
Bacula-users mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/bacula-users
