On Dec 13, 2007 9:18 AM, Gary Danko <[EMAIL PROTECTED]> wrote:
> I think I am doing something wrong in configuring my autochanger. Would
> someone who successfully uses a changer with more than one tape engine
> please post their configs so I can examine them? The field the I am not sure
> about is the "Changer Device" in the Device section.
>
> From the documentation I read: " The specified name-string must be the
> generic SCSI device name of the autochanger that corresponds to the normal
> read/write Archive Device specified in the Device resource. This generic
> SCSI device name should be specified if you have an autochanger or if you
> have a standard tape drive and want to use the Alert Command (see below)."
>
> Does this mean that in the Device section, my "Changer Device" needs to be
> the generic SCSI device name of the changer itself or of the individual tape
> drive?
>
> My setup looks like this:
>
> tape drive 0 = /dev/nst0 = /dev/sg2
> tape drive 1 = /dev/nst1 = /dev/sg3
> tape drive 2 = /dev/nst2 = /dev/sg5
> tape drive 3 = /dev/nst3 = /dev/sg6
> changer = /dev/sg4
>
> The configuration for the changer and two of its drives is below. I am not
> sure if I should change the Changer Device to /dev/sg4 for each of the
> Device entries. Any ideas?
>
> Autochanger {
> Name = Dell
> Device = ML6020-D0
> Device = ML6020-D1
> Device = ML6020-D2
> Device = ML6020-D3
> Changer Command = "/usr/local/bacula/etc/mtx-changer %c %o %S %a %d"
> Changer Device = /dev/sg4
> }
>
> Device {
> Name = ML6020-D0
> Archive Device = /dev/nst0
> Device Type = Tape
> Media Type = LTO4
> Autochanger = Yes
> Changer Device = /dev/sg2
> Alert Command = "sh -c 'tapeinfo -f %c |grep TapeAlert|cat'"
> Drive Index = 0
> Autoselect = Yes
> AlwaysOpen = Yes;
> RemovableMedia = Yes;
> RandomAccess = No;
> RequiresMount = No;
> }
>
> Device {
> Name = ML6020-D1
> Archive Device = /dev/nst1
> Device Type = Tape
> Media Type = LTO4
> Autochanger = Yes
> Changer Device = /dev/sg3
> Alert Command = "sh -c 'tapeinfo -f %c |grep TapeAlert|cat'"
> Drive Index = 1
> Autoselect = Yes
> AlwaysOpen = Yes;
> RemovableMedia = Yes;
> RandomAccess = No;
> RequiresMount = No;
> }
>
Here is my config:
I have an Exabyte224 with 2 LTO2 drives.
Autochanger {
Name = Magnum224-0
Device = LTO2-0, LTO2-1
Changer Command = "/usr/libexec/bacula/mtx-changer %c %o %S %a %d"
# Changer Device = /dev/sg5
# 02/12/2007 added udev rule to link /dev/autochanger1 to the changer
Changer Device = /dev/autochanger1
}
Device {
Name = LTO2-0
Media Type = LTO-2
Drive Index = 0
Archive Device = /dev/nst0
Autochanger=yes
AutomaticMount = yes; # when device opened, read it
AlwaysOpen = yes;
RemovableMedia = yes;
RandomAccess = no;
Spool Directory = /mnt/tmp/bacula/tape
Maximum Job Spool Size = 2G
LabelMedia = Yes
Alert Command = "sh -c 'tapeinfo -f %c |grep TapeAlert|cat'"
}
Device {
Name = LTO2-1
Media Type = LTO-2
Drive Index = 1
Archive Device = /dev/nst1
Autochanger=yes
AutomaticMount = yes; # when device opened, read it
AlwaysOpen = yes;
RemovableMedia = yes;
RandomAccess = no;
Spool Directory = /mnt/tmp/bacula/tape
Maximum Job Spool Size = 2G
LabelMedia = Yes
Alert Command = "sh -c 'tapeinfo -f %c |grep TapeAlert|cat'"
}
John
-------------------------------------------------------------------------
SF.Net email is sponsored by:
Check out the new SourceForge.net Marketplace.
It's the best place to buy or sell services
for just about anything Open Source.
http://ad.doubleclick.net/clk;164216239;13503038;w?http://sf.net/marketplace
_______________________________________________
Bacula-users mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/bacula-users
