Tim Robinson wrote:
Gavin
Here is my config:
;NT mode - extension card
[channels]
nocid=Unavailable
withheldcid=Withheld
language=en
usecallerid=yes
callwaiting=yes
nationalprefix=0
internationalprefix=00
switchtype = euroisdn
signalling = bri_net_ptmp
pridialplan=local
prilocaldialplan=local
echocancel=yes
echocancelwhenbridged=no
immediate=no
overlapdial=yes
group = 1
context=cybergear-in
channel => 1-2
Don't forget you need a cross-over cable with 100 ohm terminations....a normal ISDN/Cat5e cable will NOT work. This is a soldering iron job.
you need to know whether your current ISDN2e line is in Point to Point mode or Point to Multipoint. You then need to set the signalling parameter accordingly.
Rgds Tim
Gavin Hamill wrote:
Howdy - just got meself a cheapy Cologne chip card to play with in the hopes that it will prevail where a �1000 Eicon Diva Server failed...
I'm trying to run in NT mode and appear as a trunk to a PBX (it's an Inter-Tel Axxess unit).
If I hook a specific port on the BRI board of the PBX directly to a BT ISDN2e wallbox and dial 95000, I get a dialtone and can complete calls. Any time I connect to the Diva Server or the zaphfc card, the handset tells me 'TEST ISDN2 IS UNPLUGGED'...
I installed asterisk on a completely virgin box using the install.sh contained in the bristuff 0.2.0-RC7k tarball.
/etc/asterisk/zapata.conf [channels] switchtype = euroisdn signalling = bri_net pridialplan = dynamic prilocaldialplan = local nationalprefix = 0 internationalprefix = 00
echocancel=yes echotraining = 100 echocancelwhenbridged=yes
immediate=yes group = 1 context=demo channel => 1-2
/etc/zaptel.conf loadzone=uk defaultzone=uk
span=1,1,3,ccs,ami bchan=1-2 dchan=3
Zapata Telephony Interface Registered on major 196
PCI: Enabling device 0000:04:01.0 (0000 -> 0003)
ACPI: PCI interrupt 0000:04:01.0[A] -> GSI 17 (level, low) -> IRQ 185
zaphfc: CCD/Billion/Asuscom 2BD0 configured at mem 0xd002af00 fifo 0xcb3d8000
(0xb3d8000) IRQ 185 HZ 1000
zaphfc: Card 0 configured for NT mode
zaphfc: 1 hfc-pci card(s) in this box.
Registered tone zone 4 (United Kingdom)
zaphfc: card 0 layer 1 state = G2
<plugs cable into PBX>
zaphfc: card 0 layer 1 state = G3
zaphfc: empty HDLC frame or bad CRC received (framelen = 3, stat = 0xfe).
zaphfc: empty HDLC frame or bad CRC received (framelen = 40, stat = 0xff).
zaphfc: card 0 RX [ 0xfc 0xff 0x3 0xf 0xff 0x6d 0x1 0xff ] 8 bytes
zaphfc: card 0 RX [ 0xfc 0xff 0x3 0xf 0xf6 0x3e 0x1 0xff ] 8 bytes
zaphfc: card 0 RX [ 0xfc 0xff 0x3 0xf 0x5a 0x1f 0x1 0xff ] 8 bytes
I'm told that the RX bytes are the PBX requesting a TEI from the provider (i.e. the * box) but I can't understand why no reply is being given.
This is precisely the same problem I had with the Eicon Diva Server card...
Is this likely to be as simple as needing the 100 ohm resistors, or can it be fixed with software?
Cheers
Gavin.
_______________________________________________
Asterisk-Users mailing list
[email protected]
http://lists.digium.com/mailman/listinfo/asterisk-users
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
_______________________________________________ Asterisk-Users mailing list [email protected] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
