Is it a HP-Compaq DLXXX G4 machine? Because there is a thread here about the TE410P not generating interrupts with these servers...
On Sat, 8 Jan 2005 05:14:39 -0800 (PST), Sid <[EMAIL PROTECTED]> wrote: > Hi Scott, and Jack, > > --- Scott Stingel <[EMAIL PROTECTED]> wrote: > > > Sid- > > > > Try connecting one port to another. Note that one of the ports must be > > set up as "cpe" and the other as "net" in zapata.conf when you loop them > > together like this. > > > > A suitable crossover cable for testing can be constructed by cutting up > > a CAT 5 cable, and connecting: > > Pin 1 <--> Pin 4 on the other end > > Pin 2 <--> Pin 5 > > Pin 4 <--> Pin 1 > > Pin 5 <--> Pin 2 > > > > You should get green's on both the connected channels if your zaptel and > > zapata configurations are ok, and if you've run both modprobe and ztcfg > > as documented. > > > > Thanks for the valuable responses. We can only do the tests on monday, as the > machine is > in a data center. Other than that we have done every tests we can think of > and found in > the mailing list/wiki. The tests done at the NOC says that T1 is ok at their > end. Please > see the following information about the system: > > The machine has 4 Xeon 2.80GHz CPUs. > > This is from /proc/interrupts > 16: 0 0 0 3 IO-APIC-level usb-uhci > 19: 0 0 0 0 IO-APIC-level usb-uhci > 23: 0 0 0 0 IO-APIC-level ehci-hcd > 26: 129024 0 0 28 IO-APIC-level eth1 > 27: 0 0 21352 5 IO-APIC-level eth0 > 76: 0 0 0 0 IO-APIC-level t4xxp > > # dmesg > Zapata Telephony Interface Registered on major 196 > Specify address with base=0xNNNNN > Registered Tormenta2 PCI > Found TE410P at base address fc8ff800, remapped to f8a40800 > TE410P version c01a009b > FALC version: 00000005, Board ID: 00 > Reg 0: 0x371c9800 > Reg 1: 0x371c9000 > Reg 2: 0x07fc07fc > Reg 3: 0x00000000 > Reg 4: 0x00000000 > Reg 5: 0x00000000 > Reg 6: 0xc01a009b > Reg 7: 0x00001000 > Reg 8: 0x00000000 > Reg 9: 0x00ff0000 > Reg 10: 0x00000000 > TE410P: Launching card: 0 > TE410P: Setting up global serial parameters > Found a Wildcard: Wildcard TE410P-Xilinx > Registered tone zone 0 (United States / North America) > TE410P: Span 1 configured for ESF/B8ZS > SPAN 1: Primary Sync Source > > I am doubtful about the interrupts. Are those values ok? We have been after > this problem > for more than a week now, we have tested with 2 different cards to no success. > > I'll post the results of the crossover connection test, once we do that. > Thanks again for > the responses. > > BR, > -Sid > > > __________________________________ > Do you Yahoo!? > The all-new My Yahoo! - What will yours do? > http://my.yahoo.com > _______________________________________________ > Asterisk-Users mailing list > [email protected] > http://lists.digium.com/mailman/listinfo/asterisk-users > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users > _______________________________________________ Asterisk-Users mailing list [email protected] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
