After going through multiple posts on Internet and trying different things I can't seems get zaptel wcfxo loaded on the server correctly.
I run dual P3 500 Mhz box. After reading README.udev
I put a file 60-zaptel.rules /etc/udev/rules.d
# Section for zaptel device
KERNEL="zapctl", NAME="zap/ctl"
KERNEL="zaptimer", NAME="zap/timer"
KERNEL="zapchannel", NAME="zap/channel"
KERNEL="zappseudo", NAME="zap/pseudo"
KERNEL="zap[0-9]*", NAME="zap/%n"
In /etc/udev/permissions.d/50-udev.permissions I added:
# zaptel devices
zap/ctl:root:root:0664
zap/timer:root:root:0664
zap/channel:root:root:0664
zap/pseudo:root:root:0664
zap/*:root:root:0644
I then ran make linux26, make install, make config. I replaced insmod and rmmod in /etc/init.d/zaptel with modprobe and modprobe -r according to suggestions made in groups.
When I run modprobe wcfxo I get following:
Notice: Configuration file is /etc/zaptel.conf
line 0: Unable to open master device '/dev/zap/ctl'
1 error(s) detected
FATAL: Error running install command for wcfxo
I see zaptel and wcfxo is loaded if I run lsmod though. In 1 minute my box crashes
Rebooting the box and running it again, same thing.
/var/log/messages before crash
Dec 10 17:24:30 conference kernel: Zapata Telephony Interface Registered on major 196
Dec 10 18:36:03 conference kernel: wcfxo: DAA mode is 'FCC'
Dec 10 18:36:03 conference kernel: Uhhuh. NMI received for unknown reason 15 on CPU 0.
Dec 10 18:36:03 conference kernel: Dazed and confused, but trying to continue
Dec 10 18:36:03 conference kernel: Do you have a strange power saving mode enabled?
Dec 10 18:36:03 conference kernel: Found a Wildcard FXO: Generic Clone
Dec 10 17:24:33 conference udev[4636]: configured rule in '/etc/udev/rules.d/60-zaptel.rules' at line 4 applied, '
zapchannel' becomes 'zap/channel'
Dec 10 17:24:33 conference udev[4635]: configured rule in '/etc/udev/rules.d/60-zaptel.rules' at line 3 applied, '
zaptimer' becomes 'zap/timer'
Dec 10 17:24:33 conference udev[4636]: creating device node '/dev/zap/channel'
Dec 10 17:24:33 conference udev[4635]: creating device node '/dev/zap/timer'
Dec 10 17:24:33 conference udev[4649]: configured rule in '/etc/udev/rules.d/60-zaptel.rules' at line 5 applied, '
zappseudo' becomes 'zap/pseudo'
Dec 10 17:24:33 conference udev[4649]: creating device node '/dev/zap/pseudo'
Dec 10 17:24:33 conference udev[4650]: configured rule in '/etc/udev/rules.d/60-zaptel.rules' at line 2 applied, '
zapctl' becomes 'zap/ctl'
Dec 10 17:24:33 conference udev[4650]: creating device node '/dev/zap/ctl'
Dec 10 17:24:33 conference udev[4665]: configured rule in '/etc/udev/rules.d/60-zaptel.rules' at line 6 applied, '
zap1' becomes 'zap/%n'
Dec 10 17:24:33 conference udev[4665]: creating device node '/dev/zap/1'
After each reboot /dev/zap disappears due to udev dynamic nature I guess.
I tried to build zaptel commenting out
ifeq ($(DYNFS),)
else
@echo "**** Dynamic filesystem detected -- not creating device nodes"
@echo "**** If you are running udev, read README.udev"
endif
I see the devices created and can load wcfxpro but server crushes within less than a minute nevertheless
Has anyone have an idea? I am ready to give up on FC3 although I wonder of the hardware has anything to do with my problem.
Thanks in Advance,
Alex
|
|
_______________________________________________ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
