Isn't it supposed to be: Channel => 1
Just been through this exact same problem myself. If it is really the same, you should be able to get Asterisk working again by commenting out the "channel => xxx" lines from Zapata.conf. OK, zap channels will not work but you will know it maybe the same problem. If it is, make you are loading zaptel and wcfxo by using lsmod. My problem turned out to be that I was editing a copy of zaptel.conf in /etc/asterisk rather than the correct one in /etc If zaptel and wxfxo is loaded, you should check that ztcfg is loading the channels correctly by running ztcfg -tvvv My guess is that you will see that there are no channels created by the config utility. -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Ronald Hartmann Sent: November 04, 2004 8:18 PM To: [EMAIL PROTECTED] Subject: [Asterisk-Users] FW: ZapTel problems Good Day, Well I had the box up and running accepting an incoming pstn line. Then made a change to the zap conf file and now asterisk will not start 001�Had the box up and running 002�went to change the zapata.conf to include my pstn lines 003�and then rebooted and asterisk will not load. 004� 005�Not sure if it is a co-incidence or not 006� 007� 008�my "zapata.conf" file 009� 010�[channels] 011�language=en 012� 013�context=from-pstn 014�signalling=fxs_ks 015�faxdetect=incoming 016�usecallerid=yes 017�echocancel=yes 018�echocancelwhenbridged=no 019�echotraining=800 020�group=0 021�channel=1 022�channel=2 023� 024�context=default 025�signalling=fxo_ks 026�channel=3 027�channel=4 028� 029� 030� 031�Zaptel Configuration 032�====================== 033� 034� 035�4 channels configured. 036� 037� 038�Nov 5 13:50:14 pc-11 kernel: Zapata Telephony Interface Registered on major 196 039�Nov 5 13:50:17 pc-11 kernel: Freshmaker version: 71 040�Nov 5 13:50:17 pc-11 kernel: Freshmaker passed register test 041�Nov 5 13:50:17 pc-11 kernel: Module 0: Installed -- AUTO FXS/DPO 042�Nov 5 13:50:17 pc-11 kernel: Module 1: Installed -- AUTO FXS/DPO 043�Nov 5 13:50:17 pc-11 kernel: Module 2: Installed -- AUTO FXO (FCC mode) 044�Nov 5 13:50:17 pc-11 kernel: Module 3: Installed -- AUTO FXO (FCC mode) 045�Nov 5 13:50:17 pc-11 kernel: Found a Wildcard TDM: Wildcard TDM400P REV H (4 modules) 046� 047� 048�when i start asterisk -vvvvvc 049� [chan_phone.so] => (Linux Telephony API Support) 050� == Parsing '/etc/asterisk/phone.conf': Found 051� == Registered channel type 'Phone' (Standard Linux Telephony API Driver) 052� [chan_zap.so] => (Zapata Telephony w/PRI) 053� == Parsing '/etc/asterisk/zapata.conf': Found 054� == Unregistered channel type 'Tor' 055� == Unregistered channel type 'Zap' [EMAIL PROTECTED] asterisk]# Ouch ... error while writing audio data: : Broken pipe 057� 058� 059�Not sure where to go is this a zap issue or is it a co-incidence? 060� Any idea what I should have in my config file for a single digium 4 port card with 2 fxo and 2 fxs thanks _______________________________________________ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users _______________________________________________ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
