Re: [Asterisk-Users] Cisco PRI Gateway Problems

Peder Angvall Fri, 29 Oct 2004 13:22:02 -0700

That was it. I knew it wasn't in there, but I was just trying to call into the PRI to * and not from * out, so I didn't think it would matter. Another goofy Cisco trick I guess.

Bruce Komito wrote:

I think you are missing a dial-peer voice xxx pots entry.  E.g.:

dial-peer voice 200 pots
 description Match all inbound POTS calls
 incoming called-number T
 direct-inward-dial

I don't think the PRI will pick up the call unless the called number
matches a number in one of the pots dial-peers.

Bruce Komito
High Sierra Networks, Inc.
www.servers-r-us.com
(775) 236-5815


On Fri, 29 Oct 2004, Peder Angvall wrote:

I am trying to get a Cisco PRI gateway to send calls to * and it doesn't
appear to be working.  It is a 2610 running 12.3 IP+.  I've got the
config in there, I can see calls come into the Cisco using debugs, but I
never see it try to connect to *.  When I do debugs, I see the called #
as the 10 digit # and I see the calling # as my #, but I never see
anything on *.  Both devices can ping each other and neither is behind a
firewall.  If I do a "sip show registry" on the * box, the router is NOT
registered, but I never see any error messages either, so it looks like
it isn't even trying to register with *.  Anybody have any ideas?

Here is the relevant config from the 2610.  We are being passed a 10
digit # (I replaced the real #'s with 123456 below).

voice service voip
 signaling forward unconditional
 sip

controller T1 1/0
 framing esf
 linecode b8zs
 pri-group timeslots 1-24

interface Serial1/0:23
 no ip address
 isdn switch-type primary-ni
 isdn incoming-voice voice
 no cdp enable

voice-port 1/0:23
!
dial-peer voice 1 voip
 destination-pattern 123456....
 session protocol sipv2
 session target ipv4:192.168.1.2:5060
 session transport udp
 dtmf-relay rtp-nte
 codec g711ulaw
 no vad
!
sip-ua
 retry invite 3
 retry response 3
 retry bye 3
 retry cancel 3
 timers trying 1000
 sip-server ipv4:192.168.1.2

Here is my sip.conf:

[general]
port=5060
bindaddr=192.168.1.2
disallow=all
allow=ulaw

[192.168.1.1]
context=pstn-incoming
type=friend
host=192.168.1.1
dtmfmode=rfc2833
disallow=all
allow=ulaw

[3200]
context=local-phones
type=friend
username=3200
secret=3200
host=dynamic
mailbox=3200


_______________________________________________
Asterisk-Users mailing list
[EMAIL PROTECTED]
http://lists.digium.com/mailman/listinfo/asterisk-users
To UNSUBSCRIBE or update options visit:
  http://lists.digium.com/mailman/listinfo/asterisk-users

This message has been categorized as "Legitimate" by Bayesian Analyzer.
If you do not agree, please click on the link below to train the Analyzer.
http://216.162.162.39/bt/a.aspx?M=C:%5Csmtpmail%5CBayesTraining%5C2004-10-29%5C5bc66d662f1440aba60e35c11252071d&C=2

--
-----------------------------------------------------------------------
This message has been inspected by DynaComm i:mail
-----------------------------------------------------------------------

_______________________________________________
Asterisk-Users mailing list
[EMAIL PROTECTED]
http://lists.digium.com/mailman/listinfo/asterisk-users
To UNSUBSCRIBE or update options visit:
  http://lists.digium.com/mailman/listinfo/asterisk-users

Re: [Asterisk-Users] Cisco PRI Gateway Problems

Reply via email to