Spectro,
This configuration works fine to me. I have Merlin Legend with 2 DS1 100D cards - one goes to upstream PRI (Verizon) and the second one goes to Asterisk with T100P card. The timing is going from Verizon and asterisk configured as pri_net.
Crossover cable used between Merling Legend and Asterisk. Merling Legend is configured to Tandem PRI, so Asterisk can dial all extenstion and external numbers and all routing has been done using UDP - which is quite simple and work as charm.
There is a sample for Merlin Legend confiuraration (related to connecting between ML and (*) ) - Slot 10 => Asterisk, Slot 11 => Verizon PRI
A T1/PRI/BRI Clock Synchronization:
A Primary Secondary Tertiary
A 11/1 Loop 10/1 Loop A Slot # 10: 100D A Slot # 11: 100D-U
A 817 10/ 1 Dedicated 890 Yes Long 4 41
A 818 10/ 2 Dedicated 890 Yes Long 4 41
A 819 10/ 3 Dedicated 890 Yes Long 4 41
A 820 10/ 4 Dedicated 890 Yes Long 4 41
A 821 10/ 5 Dedicated 890 Yes Long 4 41
A 822 10/ 6 Dedicated 890 Yes Long 4 41
A 823 10/ 7 Dedicated 890 Yes Long 4 41
A 824 10/ 8 Dedicated 890 Yes Long 4 41
A 825 10/ 9 Dedicated 890 Yes Long 4 41
A 826 10/10 Dedicated 890 Yes Long 4 41
A 827 10/11 Dedicated 890 Yes Long 4 41
A 828 10/12 Dedicated 890 Yes Long 4 41
A 829 10/13 Dedicated 890 Yes Long 4 41
A 830 10/14 Dedicated 890 Yes Long 4 41
A 831 10/15 Dedicated 890 Yes Long 4 41
A 832 10/16 Dedicated 890 Yes Long 4 41
A 833 10/17 Dedicated 890 Yes Long 4 41
A 834 10/18 Dedicated 890 Yes Long 4 41
A 835 10/19 Dedicated 890 Yes Long 4 41
A 836 10/20 Dedicated 890 Yes Long 4 41
A 837 10/21 Dedicated 890 Yes Long 4 41
A 838 10/22 Dedicated 890 Yes Long 4 41
A 839 10/23 Dedicated 890 Yes Long 4 41
A 840 10/24 Dedicated Yes Long 4 A DS1 SLOT ATTRIBUTES
A Slot Type Format Supp Signal LineComp A 10 PRI ESF B8ZS DMI-MOS 2
A 11 PRI ESF B8ZS DMI-MOS 4
A PRI INFORMATION
A Slot 10 Switch: Legend-Ntwk
A Slot 11 Switch: DMS-100
A System: By extension Base number: A BchnlGrp #: Slot: TestTelNum: NtwkServ: Incoming Routing:
A 11 11 DMS-FX By Dial Plan
A Channel ID: 23 22 21 20 19 18 17 16 15 14
A 13 12 11 10 9 8 7 6 5 4
A 3 2 1
A BchnlGrp #: Slot: TestTelNum: NtwkServ: Incoming Routing:
A 80 10 ElecTandNtwk Route Directly to UDP
A Channel ID: 23 22 21 20 19 18 17 16 15 14
A 13 12 11 10 9 8 7 6 5 4
A 3 2 1
A PRI INFORMATION
A NtwkServ: VirtPrivNet A NON-LOCAL DIALPLAN
A Range Ptn Dgt Range Ptn Dgt Range Ptn Dgt
A 1) 1000-1999 01 04 18) - 35) - A 2) 2150-2169 05 04 19) - 36) - A 3) 2600-2999 02 04 20) - 37) - A 4) 3000-3999 03 04 21) - 38) - A 5) 4800-4899 06 04 22) - 39) - A 6) 7200-7399 04 04 23) - 40) - A 7) - 24) - 41) - A 8) - 25) - 42) - A 9) - 26) - 43) - A 10) - 27) - 44) - A 11) - 28) - 45) - A 12) - 29) - 46) - A 13) - 30) - 47) - A 14) - 31) - 48) - A 15) - 32) - 49) - A 16) - 33) - 50) - A 17) - 34) - A Pattern 1:
A Pool Absorb Other Digits FRL Call type A 1)890- 00 -------------------- 3 BOTH A 2)---- -- -------------------- - ----- A 3)---- -- -------------------- - ----- A 4)---- -- -------------------- - -----
A Pattern 2:
A Pool Absorb Other Digits FRL Call type A 1)890- 00 -------------------- 3 BOTH A 2)---- -- -------------------- - ----- A 3)---- -- -------------------- - ----- A 4)---- -- -------------------- - -----
A Pattern 3:
A Pool Absorb Other Digits FRL Call type A 1)890- 00 -------------------- 3 BOTH A 2)---- -- -------------------- - ----- A 3)---- -- -------------------- - ----- A 4)---- -- -------------------- - -----
A Pattern 4:
A Pool Absorb Other Digits FRL Call type A 1)890- 00 -------------------- 3 BOTH A 2)---- -- -------------------- - ----- A 3)---- -- -------------------- - ----- A 4)---- -- -------------------- - -----
A Pattern 5:
A Pool Absorb Other Digits FRL Call type A 1)890- 00 -------------------- 3 BOTH A 2)---- -- -------------------- - ----- A 3)---- -- -------------------- - ----- A 4)---- -- -------------------- - -----
A Pattern 6:
A Pool Absorb Other Digits FRL Call type A 1)890- 00 -------------------- 3 BOTH A 2)---- -- -------------------- - ----- A 3)---- -- -------------------- - ----- A 4)---- -- -------------------- - ----- A SERVICE OBSERVING INFORMATION
Steven Sokol wrote:
Spectro,
I have a T100P connected to my Merlin Magix and it works like a champ. I am using an older T1 card (one pulled from a Merlin Legend) without any problems. The card is a "100D 1 T1 Trunk" blade.
I have my system configured as a PRI (23B+D). The T100P is configured to signal with pri_net and to provide timing. I used the 5ESS protocol, but I suppose any of the PRI variants supported by both devices would work.
I do not have (or need) any CSU/DSU equipment in between the two devices. I simply built a crossover T1 cable (warning - not the same as an Ethernet cross-over cable) and connected the two devices. The card and the switch synched up and worked immediately.
The hardest part was programming the ARS table to properly make use of the connection.
As for the insertion of the new card -- I had to do a "board renumber" and it did mess with the dial plan on the switch a bit. Stations did not change, but the trunk numbering did. (This may be specific to my installation -- Magix/Legend are a field unto themselves.)
Good luck with the install. My number is below if you have additional questions.
Thanks,
Steve
Steven Sokol Owner/Manager Sokol & Associates, LLC
Phone: 816.822.1807 IaxTel: 700.613.9004 Web: http://www.sokol-associates.com
ASK ME ABOUT AstriCon 2004! http://www.astricon.net/
-----Original Message----- From: [EMAIL PROTECTED] [mailto:asterisk-users- [EMAIL PROTECTED] On Behalf Of spectro Sent: Sunday, August 22, 2004 11:25 AM To: [EMAIL PROTECTED] Subject: [Asterisk-Users] asterisk T100P to Merlin Legend
Management just approved purchase of a Digium T100P and a T1 card for our Merlin Legend Switch. I will appreciate comments from anyone performing this installation before:
- Which T1 card did you use in the Merlin Legend? - Did you require any special interface? (CSU/DSU, etc) - Any items to watch during installation.
Also we will need to remove one of our old analog Trunk cards to accomodate the new T1 interface in the switch. This switch already has two T1 cards in it. I don't know much about restriction in the Merlin Legend Switch, but our phone tech told me some horror stories about taking a card out of the switch. I know this is OT and we will probably have our switch part supplier to take care of that but I will appreciate any comments.
Thanks in advance
_______________________________________________
Asterisk-Users mailing list
[EMAIL PROTECTED]
http://lists.digium.com/mailman/listinfo/asterisk-users
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
_______________________________________________
Asterisk-Users mailing list
[EMAIL PROTECTED]
http://lists.digium.com/mailman/listinfo/asterisk-users
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
_______________________________________________ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
