On Thu, Sep 04, 2008 at 10:58:44PM -0400, sean darcy wrote: > As best i could figure it out, I've installed dahdi and rc4. > > My TDM400P doesn't answer fxo or fxs. > > /etc/dahdi/system.conf: > loadzone = us > defaultzone=us > fxoks=1,2 > fxsks=4
echocancel? > > /etc/asterisk/chan_dahdi.conf: > > [house-phones] > context=internal ; Uses the [internal] context in extensions.conf > signalling=fxo_ks ; fxo_ks Use FXO signalling for an FXS chanel > dahdichan => 1 ; Telephone attached to port 1 > dahdichan => 2 ; Telephone attached to port 2 You confuse "dahdichan" with "channel" Only the last dahdichan in a section is used. OTOH, it takes into account ther things in that section. Try: [house-phones] context=internal ; Uses the [internal] context in extensions.conf signalling=fxo_ks ; fxo_ks Use FXO signalling for an FXS chanel dahdichan => 1,2 Or, if you want to have some common settins and some different settings: [house-phones](!) context = internal ; Uses the [internal] context in extensions.conf signalling = fxo_ks ; fxo_ks Use FXO signalling for an FXS chanel group = 1 [phone1](house-phone) dahdichan = 1 callerid = Name One <456> [phone2](house-phone) callerid = Someone Else <123> group = 3 dahdichan = 2 dahdichan only works with 1.6.0 and above. > > [pstn] > context=incoming-pstn-line ; Incoming calls go to [incoming-pstn-line] > in extensions.conf > signalling=fxs_ks ; fxs_ks Use FXS signalling for an FXO channel > faxdetect=incoming > busydetect=yes > dahdichan => 4 ; PSTN attached to port 4 > > dmesg: > > dahdi: Telephony Interface Registered on major 196 > dahdi: Version: 2.0.0-rc3 > ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16 > ACPI: PCI Interrupt 0000:01:05.0[A] -> Link [APC1] -> GSI 16 (level, > low) -> IRQ 16 > PCI: Setting latency timer of device 0000:01:05.0 to 64 > Freshmaker version: 73 > Freshmaker passed register test > Clocksource tsc unstable (delta = -71426924 ns) > Module 0: Installed -- AUTO FXS/DPO > Module 1: Installed -- AUTO FXS/DPO > Module 2: Not installed > Module 3: Installed -- AUTO FXO (FCC mode) > Found a Wildcard TDM: Wildcard TDM400P REV I (3 modules) > INFO-xpp: revision trunk-r6056 MAX_XPDS=64 (8*8) > INFO-xpp: FEATURE: without BRISTUFF support > INFO-xpp: FEATURE: with PROTOCOL_DEBUG > INFO-xpp: FEATURE: with sync_tick() from DAHDI > INFO-xpp_usb: revision trunk-r6056 > usbcore: registered new interface driver xpp_usb > dahdi: Registered tone zone 0 (United States / North America) > > dahdi_scan > [1] > active=yes > alarms=OK > description=Wildcard TDM400P REV I Board 5 > name=WCTDM/4 > manufacturer=Digium > devicetype=Wildcard TDM400P REV I > location=PCI Bus 01 Slot 06 > basechan=1 > totchans=4 > irq=16 > type=analog > port=1,FXS > port=2,FXS > port=3,none > port=4,FXO What is the output of: cat /proc/dahdi/* > > CLI> dahdi show status > Description Alarms IRQ bpviol CRC4 > Fra Codi Options LBO > Wildcard TDM400P REV I Board 5 OK 0 0 0 > CAS Unk YEL 0 db (CSU)/0-133 feet (DSX-1) > > But if I dial in, no dial tone, nothing on the cli. > And: > > *CLI> dahdi show channels > Chan Extension Context Language MOH Interpret > Blocked State > pseudo default default > In Service > > Tried dahdi_genconf. No help. > > Reverted now. > > Any help appreciated. > > seam > > > _______________________________________________ > -- Bandwidth and Colocation Provided by http://www.api-digital.com -- > > AstriCon 2008 - September 22 - 25 Phoenix, Arizona > Register Now: http://www.astricon.net > > asterisk-users mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users -- Tzafrir Cohen icq#16849755 jabber:[EMAIL PROTECTED] +972-50-7952406 mailto:[EMAIL PROTECTED] http://www.xorcom.com iax:[EMAIL PROTECTED]/tzafrir _______________________________________________ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- AstriCon 2008 - September 22 - 25 Phoenix, Arizona Register Now: http://www.astricon.net asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
