Hello Moises. I enabled debug mode in asterisk. When I dial, I get:
Jul 19 14:24:38 DEBUG[4463]: build_route: Contact hop:
<sip:192.168.0.6:5060>
Jul 19 14:24:38 VERBOSE[4463]: -- Executing
Dial("SIP/192.168.0.6-08137090", "Zap/1/4502") in new stack
Jul 19 14:24:38 NOTICE[4463]: Unable to create channel of type 'Zap'
Jul 19 14:24:38 VERBOSE[4463]: == Everyone is busy/congested at this
time
Jul 19 14:24:38 DEBUG[4463]: Exiting with DIALSTATUS=CHANUNAVAIL.
zttool say:
OK Digium Wildcard TE110P T1/E1 Card 0
Current Alarms: No alarms.
Sync Source: Internally clocked
IRQ Misses: 14
Bipolar Viol: 0
Tx/Rx Levels: 0/ 0
Total/Conf/Act: 31/ 31/ 0
1111111111222222222333
1234567890123456789012345789012
I thing that the other end it's ok because I can close the ISDN Link
between the two machines.
Thanks
Lincoln
Moises Silva wrote:
Are you sure the other end is configured properly?
What does "zttool" says?
Have you turned on all the asterisk debug messages to look further?
Regards
On 7/19/06, Lincoln Zuljewic Silva <[EMAIL PROTECTED]> wrote:
Hello all. I have a Digitum TE110P board configured and working (I
think
that it's working). When I configure in extensions.conf to a extension
route
to that board I get "Unable to create channel of type 'Zap'" on log.
Here are some configuration:
lspci -vv
0000:01:07.0 Network controller: Tiger Jet Network Inc. Tiger3XX
Modem/ISDN
interface
Subsystem: Unknown device 795e:0001
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (250ns min, 32000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at c800 [size=256]
Region 1: Memory at fc5ff000 (32-bit, non-prefetchable)
[size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=0mA
PME(D0+,D1-,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
ztcfg -vv
Zaptel Configuration
======================
SPAN 1: CAS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1)
Channel map:
Channel 01: Individual Clear channel (Default) (Slaves: 01)
Channel 02: Individual Clear channel (Default) (Slaves: 02)
Channel 03: Individual Clear channel (Default) (Slaves: 03)
Channel 04: Individual Clear channel (Default) (Slaves: 04)
Channel 05: Individual Clear channel (Default) (Slaves: 05)
Channel 06: Individual Clear channel (Default) (Slaves: 06)
Channel 07: Individual Clear channel (Default) (Slaves: 07)
Channel 08: Individual Clear channel (Default) (Slaves: 08)
Channel 09: Individual Clear channel (Default) (Slaves: 09)
Channel 10: Individual Clear channel (Default) (Slaves: 10)
Channel 11: Individual Clear channel (Default) (Slaves: 11)
Channel 12: Individual Clear channel (Default) (Slaves: 12)
Channel 13: Individual Clear channel (Default) (Slaves: 13)
Channel 14: Individual Clear channel (Default) (Slaves: 14)
Channel 15: Individual Clear channel (Default) (Slaves: 15)
Channel 16: D-channel (Default) (Slaves: 16)
Channel 17: Individual Clear channel (Default) (Slaves: 17)
Channel 18: Individual Clear channel (Default) (Slaves: 18)
Channel 19: Individual Clear channel (Default) (Slaves: 19)
Channel 20: Individual Clear channel (Default) (Slaves: 20)
Channel 21: Individual Clear channel (Default) (Slaves: 21)
Channel 22: Individual Clear channel (Default) (Slaves: 22)
Channel 23: Individual Clear channel (Default) (Slaves: 23)
Channel 24: Individual Clear channel (Default) (Slaves: 24)
Channel 25: Individual Clear channel (Default) (Slaves: 25)
Channel 26: Individual Clear channel (Default) (Slaves: 26)
Channel 27: Individual Clear channel (Default) (Slaves: 27)
Channel 28: Individual Clear channel (Default) (Slaves: 28)
Channel 29: Individual Clear channel (Default) (Slaves: 29)
Channel 30: Individual Clear channel (Default) (Slaves: 30)
Channel 31: Individual Clear channel (Default) (Slaves: 31)
31 channels configured.
My zaptel.cfg
span=1,0,0,cas,hdb3
loadzone=us
defaultzone=us
bchan=1-15,17-31
dchan=16
My zapata.conf
[channels]
context=customer
signalling=pri_cpe
channel => 1
My extensions.conf
exten => 4502,1,Dial(Zap/1/4502)
show channels in Asterisk CLI:
Channel (Context Extension Pri ) State Appl.
Data
0 active channel(s)
zap show channels in Asterisk CLI:
Chan Extension Context Language MusicOnHold
pseudo customer
1 customer
zap show channel 1 in Asterisk CLI:
hannel: 1>
File Descriptor: 10
Span: 1
Extension:
Dialing: no
Context: corsidian
Caller ID string:
Destroy: 0
InAlarm: 0
Signalling Type: PRI Signalling
Owner: <None>
Real: <None>
Callwait: <None>
Threeway: <None>
Confno: -1
Propagated Conference: -1
Real in conference: 0
DSP: no
Relax DTMF: no
Dialing/CallwaitCAS: 0/0
Default law: alaw
Fax Handled: no
Pulse phone: no
Echo Cancellation: 0 taps unless TDM bridged, currently OFF
PRI Flags:
PRI Logical Span: Implicit
Actual Hookstate: Onhook
When I dial 4502 in the softphone I get "Unable to create channel of
type
'Zap'".
Could anybody give to me a little help ?
Thanks a lot !
Lincoln
_______________________________________________
--Bandwidth and Colocation provided by Easynews.com --
asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
|
_______________________________________________
--Bandwidth and Colocation provided by Easynews.com --
asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
