Add direct-inward-dial to your dial peer and it should work fine. -Greg
On Mon, 2005-10-03 at 15:48 -0700, Tim Pozar wrote: > I would think I could do this but for some reason I am stymied. > > I have a PRI from RCN connected to a cisco 3640 (in my day "cisco" is > all lower case :-)). My config looks something like this on the cisco... > --------------------------------------------------------- > voice-card 3 > dsp services dspfarm > ! > ip cef > ! > isdn switch-type primary-5ess > ! > controller T1 3/0 > framing esf > linecode b8zs > pri-group timeslots 1-24 > description RCN PRI at SF7 > ! > interface FastEthernet1/0 > no ip address > duplex auto > speed auto > ! > interface Serial3/0:23 > no ip address > dialer-group 1 > isdn switch-type primary-5ess > isdn incoming-voice voice > no cdp enable > ! > voice-port 3/0:23 > connection plar 1000 > ! > dial-peer cor custom > ! > dial-peer voice 1 voip > destination-pattern 1000 > session protocol sipv2 > session target ipv4:1.2.3.4:5060 > session transport udp > dtmf-relay rtp-nte > codec g711ulaw > no vad > ! > dial-peer voice 2 pots > destination-pattern 9T > port 3/0:23 > ! > sip-ua > retry invite 3 > retry response 3 > retry bye 3 > retry cancel 3 > timers trying 1000 > sip-server ipv4:1.2.3.5 > ! > --------------------------------------------------------- > But of course with that what get's set as the DID number is "1000". I > need to find out how to get the DID number passed to asterisk. Any > thoughts from folks out there? > > Thanks... > Tim > > PS... Here is a show ver from the 3640... > > vr01-200p-sfo>show ver > Cisco Internetwork Operating System Software > IOS (tm) 3600 Software (C3640-IS-M), Version 12.3(16), RELEASE SOFTWARE > (fc4) > Technical Support: http://www.cisco.com/techsupport > Copyright (c) 1986-2005 by cisco Systems, Inc. > Compiled Tue 23-Aug-05 20:03 by ssearch > Image text-base: 0x60008B00, data-base: 0x61BFA000 > > ROM: System Bootstrap, Version 11.1(19)AA, EARLY DEPLOYMENT RELEASE > SOFTWARE (fc1) > ROM: 3600 Software (C3640-IS-M), Version 12.3(16), RELEASE SOFTWARE (fc4) > > vr01-200p-sfo uptime is 3 weeks, 3 days, 22 hours, 22 minutes > System returned to ROM by reload at 00:24:09 UTC Fri Sep 9 2005 > System restarted at 00:25:48 UTC Fri Sep 9 2005 > System image file is "flash:flash:c3640-is-mz.123-16.bin" > > cisco 3640 (R4700) processor (revision 0x00) with 124928K/6144K bytes of > memory. > Processor board ID 10311643 > R4700 CPU at 100MHz, Implementation 33, Rev 1.0 > Bridging software. > X.25 software, Version 3.0.0. > SuperLAT software (copyright 1990 by Meridian Technology Corp). > Primary Rate ISDN software, Version 1.1. > 2 FastEthernet/IEEE 802.3 interface(s) > 24 Serial network interface(s) > 1 Channelized T1/PRI port(s) > DRAM configuration is 64 bits wide with parity disabled. > 125K bytes of non-volatile configuration memory. > 32768K bytes of processor board System flash (Read/Write) > _______________________________________________ > --Bandwidth and Colocation sponsored by Easynews.com -- > > Asterisk-Users mailing list > [email protected] > http://lists.digium.com/mailman/listinfo/asterisk-users > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users _______________________________________________ --Bandwidth and Colocation sponsored by Easynews.com -- Asterisk-Users mailing list [email protected] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
