[Asterisk-Users] Working with FWD, IPTel, SIPPhone?

[Ian Blenke]

I'll admit it. I'm a asterisk newbie (but no stranger to telephony).

The setup is simple: two Grandstream BudgeTel 100 phones (SIPPhone 
specials) on a private segment calling to a Linux box acting as the 
segment's firewall with a leg on our public network. The phones are 
setup as SIP/phone1 (x1000) and SIP/phone2 (x1001), respectively (thanks 
to the Asterisk HOWTO).

Getting IAX to work with IAXTEL wasn't a problem, but I'm still fighting 
with inbound/outbound VoIP "trunks" with IAX2 or anything SIP. I can 
call 1700NXXNXXX IAXTEL numbers, and anything gatewayed from that 
network (ie, FWD 170099XXXXX gatewayed numbers work).

To get FWD, IPTel, or SIPPhone to work, I've deduced I need to do 
something like the following after reading various online email archives 
(please correct me if I'm wrong):

	sip.conf:

         [general]
         register => XXXXX:[EMAIL PROTECTED]/1000
         register => 1747XXXXXXX:[EMAIL PROTECTED]/1000
         register => username:[EMAIL PROTECTED]/1000
        extensions.conf:
         [default]
         include=sip
         [sip]
         include=sip
         [fwd]
         exten => _91339.,1,SetCallerID(XXXXX)
         exten => _91339.,2,Dial,SIP/${EXTEN:[EMAIL PROTECTED],tr
         exten => _91747.,1,SetCallerID(1747XXXXXXX)
         exten => _91747.,2,Dial,SIP/${EXTEN:[EMAIL PROTECTED],tr
         exten => _91478.,1,SetCallerID(XXXXXXXX)
         exten => _91478.,2,Dial,SIP/${EXTEN:[EMAIL PROTECTED],tr
Unfortunately, this doesn't appear to work. Nor do any other 
translations (even a simple "_8." doesn't work). No matter what I try, I 
keep getting "404 Not found" or "all circuits are busy" messages.

As far as I can tell, I'm registered with with all three SIP providers:

        *CLI> sip show registry
        195.37.77.101:5060    username         120 Registered
        192.246.69.223:5060   XXXXX            120 Registered
        130.94.123.252:5060   1747XXXXXX       120 Registered
I'm also apparently registered correctly with IAX and IAX2:

        *CLI> iax show registry
        Host               Username  Perceived      Refresh  State
        12.37.165.130:5036 username 66.x.x.x:5036 60 Registered
        
        *CLI> iax2 show registry
        Host               Username  Perceived      Refresh  State
        12.37.165.130:4569 username 66.x.x.x:4569 60 Registered
Unfortunately(?), any calls through IAX2 never seem to go through.

While I'd like to eventually setup an outbound NAT proxy, I've had a 
difficult time decyphering how to configure SER, siproxd, or PartySIP to 
register to external SIP providers like FWD, IPTel, and SIPPhone. I'm 
guessing this is what the additional sections in sip.conf are for?

	sip.conf

         ;; Free World Dialup Proxy
         [fwd.pulver.com]
         type=friend
         host=fwd.pulver.com
         fromuser=48702
         fromdomain=fwd.pulver.com
         ;secret=password
         ;username=XXXXX
Do you need these sections if you're not NATting? How would I define 
fwdnat.pulver.com:5082 above? (asterisk appears to treat the whole 
string as a hostname).

At some point, I'd like to have branch offices off of IPSEC tunnelled 
connections - running an Asterisk instance on every customer's firewall 
isn't as appealing as a simple SIP proxy.

I guess the confusion is: how do you setup a SIP Provider *and* an 
outbound proxy (either locally on my linux firewall, or provided by the 
SIP carrier?)

This really could use a good HOWTO/FAQ, but for the life of me I can't 
find it (if someone would take the time to guide me a bit with this, I 
wouldn't mind taking a stab at writing one).

Thanks,

--
- Ian C. Blenke <[EMAIL PROTECTED]>
(This message bound by the following:
http://www.nks.net/email_disclaimer.html)
_______________________________________________
Asterisk-Users mailing list
[EMAIL PROTECTED]
http://lists.digium.com/mailman/listinfo/asterisk-users