> That is an expected result. 256MB is not enough for the VRAM BAR and the > doorbell BAR to fit into. But you can still use VGA emulation that way if > I'm not completely mistaken. >
Hmm, then what procedure should I follow to take a VGA output. It seems Graphic Card does not have a VGA output. And isn't there any way to use this GPU with a 256MB buffered PCIe? > Then I canged 256 MB to 4GB in .dtsi and U-boot conf file. > > How did you do this? Is your memory layout consistent? > > See when you just changed one end address you might need to adjust other > addresses as well. > > Regards, > Christian. > It's not consistent I seems. At first I changed .dtsi like it's consistent. I only changed PCIe1 Device Memory and I/O range. It gave same error. Then I also changed PCIe2 and PCIe3 devices starting adress according to PCIe1 device end adress in .dtsi. I am not sure I made this correctly or not but it gave same result again. This is why I asked "If it is, is there any sample PCIe configuration for E9171?". *This is a code piece from my T104xRDB.h file which is contain PCIe configuration variables for U-boot. I made changes like it's not consistent. RAM size is 8 GB.* #ifdef CONFIG_PCI /* controller 1, direct to uli, tgtid 3, Base address 20000 */ #ifdef CONFIG_PCIE1 #define CONFIG_SYS_PCIE1_MEM_VIRT *0x80000000* #define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull #define CONFIG_SYS_PCIE1_MEM_SIZE *0x10000000 /* 256M */* #define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 #define CONFIG_SYS_PCIE1_IO_PHYS *0xff8000000ull* #define CONFIG_SYS_PCIE1_IO_SIZE *0x00010000 /* 64k */* #endif /* controller 2, Slot 2, tgtid 2, Base address 201000 */ #ifdef CONFIG_PCIE2 #define CONFIG_SYS_PCIE2_MEM_VIRT *0x90000000* #define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xc10000000ull #define CONFIG_SYS_PCIE2_MEM_SIZE* 0x100000000 /* 4GB */* #define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 #define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull #define CONFIG_SYS_PCIE2_IO_SIZE *0x00100000 /* 1M */* #endif /* controller 3, Slot 1, tgtid 1, Base address 202000 */ #ifdef CONFIG_PCIE3 #define CONFIG_SYS_PCIE3_MEM_VIRT *0x190000000 /* I changed this to 0x190000000 instead of 0xa0000000 because PCIE2 end adress is changed. End adress is to 4 GB (0x100000000 hex so I added 0x90000000 with 100000000) */* #define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 #define CONFIG_SYS_PCIE3_MEM_PHYS 0xd10000000ull #define CONFIG_SYS_PCIE3_MEM_SIZE 0x10000000 /* 256M */ #define CONFIG_SYS_PCIE3_IO_VIRT 0xf8110000 #define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 #define CONFIG_SYS_PCIE3_IO_PHYS *0xff8110000ull /* Did same things for IO * #define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ #endif /* controller 4, Base address 203000 */ #ifdef CONFIG_PCIE4 #define CONFIG_SYS_PCIE4_MEM_VIRT *0x200000000 /* SAME STEP WITH PCIE3. This time I added with 256 MB (0x10000000) */* #define CONFIG_SYS_PCIE4_MEM_BUS 0xe0000000 #define CONFIG_SYS_PCIE4_MEM_PHYS 0xd20000000ull #define CONFIG_SYS_PCIE4_MEM_SIZE 0x10000000 /* 256M */ #define CONFIG_SYS_PCIE4_IO_VIRT 0xf8120000 #define CONFIG_SYS_PCIE4_IO_BUS 0x00000000 #define CONFIG_SYS_PCIE4_IO_PHYS *0xff8120000ull /* Did same things for IO * #define CONFIG_SYS_PCIE4_IO_SIZE 0x00010000 /* 64k */ #endif Am 02.12.19 um 14:32 schrieb Yusuf Altıparmak: > > >> I attached my dts file. >> >> System is working fine when GPU is not plugged in. >> >> *This is the last console log before freeze:* >> [drm] amdgpu kernel modesetting enabled. >> >> [drm] initializing kernel modesetting (POLARIS12 0x1002:0x6987 >> 0x1787:0x2389 0x80). >> [drm] register mmio base: 0x20200000 >> >> fsl-fman-port ffe488000.port fm1-gb0: renamed from eth0 >> >> [drm] register mmio size: 262144 >> >> [drm] add ip block number 0 <vi_common> >> >> [drm] add ip block number 1 <gmc_v8_0> >> >> [drm] add ip block number 2 <tonga_ih> >> >> [drm] add ip block number 3 <powerplay> >> >> [drm] add ip block number 4 <dm> >> >> [drm] add ip block number 5 <gfx_v8_0> >> >> [drm] add ip block number 6 <sdma_v3_0> >> >> [drm] add ip block number 7 <uvd_v6_0> >> >> [drm] add ip block number 8 <vce_v3_0> >> >> [drm] UVD is enabled in VM mode >> >> [drm] UVD ENC is enabled in VM mode >> >> [drm] VCE enabled in VM mode >> >> ATOM BIOS: 113-ER16BFC-001 >> >> [drm] GPU posting now... >> >> Disabling lock debugging due to kernel taint >> >> Machine check in kernel mode. >> >> Caused by (from MCSR=a000): Load Error Report >> >> Guarded Load Error Report >> >> Kernel panic - not syncing: Unrecoverable Machine check >> >> CPU: 1 PID: 2023 Comm: udevd Tainted: G M 4.19.26+gc0c2141 >> #1 >> Call Trace: >> >> >> >> _______________________________________________ >> amd-gfx mailing >> [email protected]https://lists.freedesktop.org/mailman/listinfo/amd-gfx >> >> <https://nam11.safelinks.protection.outlook.com/?url=https%3A%2F%2Flists.freedesktop.org%2Fmailman%2Flistinfo%2Famd-gfx&data=02%7C01%7Cchristian.koenig%40amd.com%7C9be244504efb4ff9cc0a08d7772c1630%7C3dd8961fe4884e608e11a82d994e183d%7C0%7C0%7C637108903547899069&sdata=OL4UKczXinKq5FM3Cid5kYcESkHAl0esXfOB83AUPU8%3D&reserved=0> >> >> >> > > Christian König <[email protected]>, 2 Ara 2019 Pzt, 15:28 > tarihinde şunu yazdı: > >> Hi Yusuf, >> >> Am 02.12.19 um 12:41 schrieb Yusuf Altıparmak: >> >> My embedded board is freezing when I put E9171 on PCIe. What is the >> meaning of Unrecoverable Machine Check error about GPU? >> >> >> Well see the explanation on Wikipedia for example: >> https://en.wikipedia.org/wiki/Machine-check_exception >> <https://nam11.safelinks.protection.outlook.com/?url=https%3A%2F%2Fen.wikipedia.org%2Fwiki%2FMachine-check_exception&data=02%7C01%7Cchristian.koenig%40amd.com%7C9be244504efb4ff9cc0a08d7772c1630%7C3dd8961fe4884e608e11a82d994e183d%7C0%7C0%7C637108903547909070&sdata=mBxI9LnRBO4iu5oyHc9OrrFj0K10SiOf5%2FztzmNedaI%3D&reserved=0> >> >> In general it means you have messed up something in your hardware >> configuration. >> >> Could PCIe settings in .dts file cause this problem? >> >> >> Possible, but rather unlikely. My best guess is that it is some problem >> with the power supply. >> >> If it is, is there any sample PCIe configuration for E9171? >> >> >> The E9171 is just a PCIe device, so the dtsi is actually rather >> uninteresting. What we really need is a full dmesg and maybe lspci output >> would help as well. >> >> Regards, >> Christian. >> > > > Hi Christian, > > At first, I am using NXP T1042D4RDB-64B which has 256 MB PCIe buffer > according to its. PCIe memory range was arranged to 256 MB in .dts file and > in U-boot configuration file. Driver was giving error with exit code -12 > (OUT_OF_MEMORY). But I was able to reach the linux console. > > [ 5.512922] [drm] amdgpu kernel modesetting enabled. > [ 5.517065] [drm] initializing kernel modesetting (POLARIS12 > 0x1002:0x6987 0x1787:0x2389 0x80). > [ 5.524507] amdgpu 0001:01:00.0: Fatal error during GPU init > [ 5.529296] amdgpu: probe of 0001:01:00.0 failed with error -12 > > Then I canged 256 MB to 4GB in .dtsi and U-boot conf file. I also changed > 64KB I/O size to 1MB . When I do this, I wasn't able to reach the linux > console because board was freezing. But driver was successfull at this > time. I already mentioned successfull driver console logs up. > > *this is lspci -v when GPU is plugged and Memory size is 256 MB.* > > root@t1042d4rdb-64b:~# lspci -v > 0000:00:00.0 PCI bridge: Freescale Semiconductor Inc Device 0824 (rev 11) > (prog-if 00 [Normal decode]) > Device tree node: /sys/firmware/devicetree/base/pcie@ffe240000 > /pcie@0 > Flags: bus master, fast devsel, latency 0, IRQ 20 > Memory at <ignored> (32-bit, non-prefetchable) > Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 > I/O behind bridge: 00000000-0000ffff [size=64K] > Memory behind bridge: e0000000-efffffff [size=256M] > Prefetchable memory behind bridge: None > Capabilities: [44] Power Management version 3 > Capabilities: [4c] Express Root Port (Slot-), MSI 00 > Capabilities: [100] Advanced Error Reporting > Kernel driver in use: pcieport > > 0001:00:00.0 PCI bridge: Freescale Semiconductor Inc Device 0824 (rev 11) > (prog-if 00 [Normal decode]) > Device tree node: /sys/firmware/devicetree/base/pcie@ffe250000 > /pcie@0 > Flags: bus master, fast devsel, latency 0, IRQ 21 > Memory at <ignored> (32-bit, non-prefetchable) > Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 > I/O behind bridge: 00000000-0000ffff [size=64K] > Memory behind bridge: e0000000-efffffff [size=256M] > Prefetchable memory behind bridge: None > Capabilities: [44] Power Management version 3 > Capabilities: [4c] Express Root Port (Slot-), MSI 00 > Capabilities: [100] Advanced Error Reporting > Kernel driver in use: pcieport > > 0001:01:00.0 VGA compatible controller: Advanced Micro Devices, Inc. > [AMD/ATI] Lexa [Radeon E9171 MCM] (rev 80) (prog-if 00 [VGA controller]) > Subsystem: Hightech Information System Ltd. Device 2389 > Flags: fast devsel, IRQ 41 > Memory at c10000000 (64-bit, prefetchable) [size=256M] > Memory at <ignored> (64-bit, prefetchable) > I/O ports at 1100 [size=256] > Memory at <ignored> (32-bit, non-prefetchable) > Expansion ROM at <ignored> [disabled] > Capabilities: [48] Vendor Specific Information: Len=08 <?> > Capabilities: [50] Power Management version 3 > Capabilities: [58] Express Legacy Endpoint, MSI 00 > Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit+ > Capabilities: [100] Vendor Specific Information: ID=0001 Rev=1 > Len=010 <?> > Capabilities: [150] Advanced Error Reporting > Capabilities: [200] Resizable BAR <?> > Capabilities: [270] Secondary PCI Express <?> > Capabilities: [2b0] Address Translation Service (ATS) > Capabilities: [2c0] Page Request Interface (PRI) > Capabilities: [2d0] Process Address Space ID (PASID) > Capabilities: [320] Latency Tolerance Reporting > Capabilities: [328] Alternative Routing-ID Interpretation (ARI) > Capabilities: [370] L1 PM Substates > Kernel modules: amdgpu > > 0001:01:00.1 Audio device: Advanced Micro Devices, Inc. [AMD/ATI] Device > aae0 > Subsystem: Hightech Information System Ltd. Device aae0 > Flags: bus master, fast devsel, latency 0, IRQ 17 > Memory at <ignored> (64-bit, non-prefetchable) > Capabilities: [48] Vendor Specific Information: Len=08 <?> > Capabilities: [50] Power Management version 3 > Capabilities: [58] Express Legacy Endpoint, MSI 00 > Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit+ > Capabilities: [100] Vendor Specific Information: ID=0001 Rev=1 > Len=010 <?> > Capabilities: [150] Advanced Error Reporting > Capabilities: [328] Alternative Routing-ID Interpretation (ARI) > > 0002:00:00.0 PCI bridge: Freescale Semiconductor Inc Device 0824 (rev 11) > (prog-if 00 [Normal decode]) > Device tree node: /sys/firmware/devicetree/base/pcie@ffe260000 > /pcie@0 > Flags: bus master, fast devsel, latency 0, IRQ 22 > Memory at <ignored> (32-bit, non-prefetchable) > Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 > I/O behind bridge: 00000000-0000ffff [size=64K] > Memory behind bridge: e0000000-efffffff [size=256M] > Prefetchable memory behind bridge: None > Capabilities: [44] Power Management version 3 > Capabilities: [4c] Express Root Port (Slot-), MSI 00 > Capabilities: [100] Advanced Error Reporting > Kernel driver in use: pcieport > > 0003:00:00.0 PCI bridge: Freescale Semiconductor Inc Device 0824 (rev 11) > (prog-if 00 [Normal decode]) > Device tree node: /sys/firmware/devicetree/base/pcie@ffe270000 > /pcie@0 > Flags: bus master, fast devsel, latency 0, IRQ 23 > Memory at <ignored> (32-bit, non-prefetchable) > Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 > I/O behind bridge: 00000000-0000ffff [size=64K] > Memory behind bridge: e0000000-efffffff [size=256M] > Prefetchable memory behind bridge: None > Capabilities: [44] Power Management version 3 > Capabilities: [4c] Express Root Port (Slot-), MSI 00 > Capabilities: [100] Advanced Error Reporting > Kernel driver in use: pcieport > > *AND This is PCIe dmesg message when memory range is 256MB. It's also > giving same message when memory range is arranged as 4GB;* > > PCI host bridge /pcie@ffe240000 ranges: > MEM 0x0000000c00000000..0x0000000c0fffffff -> 0x00000000e0000000 > IO 0x0000000ff8000000..0x0000000ff800ffff -> 0x0000000000000000 > /pcie@ffe240000: PCICSRBAR @ 0xff000000 > setup_pci_atmu: end of DRAM 200000000 > /pcie@ffe240000: Setup 64-bit PCI DMA window > /pcie@ffe240000: WARNING: Outbound window cfg leaves gaps in memory map. > Adjusting the memory map could reduce unnecessary bounce buffering. > /pcie@ffe240000: DMA window size is 0xe0000000 > Found FSL PCI host bridge at 0x0000000ffe250000. Firmware bus number: 0->1 > PCI host bridge /pcie@ffe250000 ranges: > MEM 0x0000000c10000000..0x0000000c1fffffff -> 0x00000000e0000000 > IO 0x0000000ff8010000..0x0000000ff801ffff -> 0x0000000000000000 > /pcie@ffe250000: PCICSRBAR @ 0xff000000 > setup_pci_atmu: end of DRAM 200000000 > /pcie@ffe250000: Setup 64-bit PCI DMA window > /pcie@ffe250000: WARNING: Outbound window cfg leaves gaps in memory map. > Adjusting the memory map could reduce unnecessary bounce buffering. > /pcie@ffe250000: DMA window size is 0xe0000000 > Found FSL PCI host bridge at 0x0000000ffe260000. Firmware bus number: 0->0 > PCI host bridge /pcie@ffe260000 ranges: > MEM 0x0000000c20000000..0x0000000c2fffffff -> 0x00000000e0000000 > IO 0x0000000ff8020000..0x0000000ff802ffff -> 0x0000000000000000 > /pcie@ffe260000: PCICSRBAR @ 0xff000000 > setup_pci_atmu: end of DRAM 200000000 > /pcie@ffe260000: Setup 64-bit PCI DMA window > /pcie@ffe260000: WARNING: Outbound window cfg leaves gaps in memory map. > Adjusting the memory map could reduce unnecessary bounce buffering. > /pcie@ffe260000: DMA window size is 0xe0000000 > Found FSL PCI host bridge at 0x0000000ffe270000. Firmware bus number: 0->0 > PCI host bridge /pcie@ffe270000 ranges: > MEM 0x0000000c30000000..0x0000000c3fffffff -> 0x00000000e0000000 > IO 0x0000000ff8030000..0x0000000ff803ffff -> 0x0000000000000000 > /pcie@ffe270000: PCICSRBAR @ 0xff000000 > setup_pci_atmu: end of DRAM 200000000 > /pcie@ffe270000: Setup 64-bit PCI DMA window > /pcie@ffe270000: WARNING: Outbound window cfg leaves gaps in memory map. > Adjusting the memory map could reduce unnecessary bounce buffering. > /pcie@ffe270000: DMA window size is 0xe0000000 > iommu: Adding device ff6000000.qman-portal to group 0 > iommu: Adding device ff6004000.qman-portal to group 1 > iommu: Adding device ff6008000.qman-portal to group 2 > iommu: Adding device ff600c000.qman-portal to group 3 > iommu: Adding device ff6010000.qman-portal to group 4 > iommu: Adding device ff6014000.qman-portal to group 5 > iommu: Adding device ff6018000.qman-portal to group 6 > iommu: Adding device ff601c000.qman-portal to group 7 > iommu: Adding device ff6020000.qman-portal to group 8 > iommu: Adding device ff6024000.qman-portal to group 9 > iommu: Adding device ffe100300.dma to group 10 > iommu: Adding device ffe101300.dma to group 11 > iommu: Adding device ffe114000.sdhc to group 12 > iommu: Adding device ffe210000.usb to group 13 > iommu: Adding device ffe211000.usb to group 14 > iommu: Adding device ffe220000.sata to group 15 > iommu: Adding device ffe221000.sata to group 16 > iommu: Adding device ffe318000.qman to group 17 > iommu: Adding device ffe31a000.bman to group 18 > iommu: Adding device ffe240000.pcie to group 19 > iommu: Adding device ffe250000.pcie to group 20 > iommu: Adding device ffe260000.pcie to group 21 > iommu: Adding device ffe270000.pcie to group 22 > iommu: Adding device ffe140000.qe to group 23 > software IO TLB: mapped [mem 0xfbfff000-0xfffff000] (64MB) > PCI: Probing PCI hardware > fsl-pci ffe240000.pcie: PCI host bridge to bus 0000:00 > pci_bus 0000:00: root bus resource [io > 0x8000080000010000-0x800008000001ffff] (bus address [0x0000-0xffff]) > pci_bus 0000:00: root bus resource [mem 0xc00000000-0xc0fffffff] (bus > address [0xe0000000-0xefffffff]) > pci_bus 0000:00: root bus resource [bus 00] > iommu: Removing device ffe240000.pcie from group 19 > iommu: Adding device 0000:00:00.0 to group 24 > pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring > pci 0000:00:00.0: PCI bridge to [bus 01-ff] > fsl-pci ffe250000.pcie: PCI host bridge to bus 0001:00 > pci_bus 0001:00: root bus resource [io > 0x8000080000021000-0x8000080000030fff] (bus address [0x0000-0xffff]) > pci_bus 0001:00: root bus resource [mem 0xc10000000-0xc1fffffff] (bus > address [0xe0000000-0xefffffff]) > pci_bus 0001:00: root bus resource [bus 00-01] > iommu: Removing device ffe250000.pcie from group 20 > iommu: Adding device 0001:00:00.0 to group 19 > pci 0001:01:00.0: enabling Extended Tags > pci 0001:01:00.0: 4.000 Gb/s available PCIe bandwidth, limited by 5 GT/s > x1 link at 0001:00:00.0 (capable of 63.008 Gb/s with 8 GT/s x8 link) > iommu: Adding device 0001:01:00.0 to group 19 > pci 0001:01:00.1: enabling Extended Tags > iommu: Adding device 0001:01:00.1 to group 19 > pci 0001:00:00.0: PCI bridge to [bus 01-ff] > fsl-pci ffe260000.pcie: PCI host bridge to bus 0002:00 > pci_bus 0002:00: root bus resource [io > 0x8000080000032000-0x8000080000041fff] (bus address [0x0000-0xffff]) > pci_bus 0002:00: root bus resource [mem 0xc20000000-0xc2fffffff] (bus > address [0xe0000000-0xefffffff]) > pci_bus 0002:00: root bus resource [bus 00] > iommu: Removing device ffe260000.pcie from group 21 > iommu: Adding device 0002:00:00.0 to group 20 > pci 0002:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring > pci 0002:00:00.0: PCI bridge to [bus 01-ff] > fsl-pci ffe270000.pcie: PCI host bridge to bus 0003:00 > pci_bus 0003:00: root bus resource [io > 0x8000080000043000-0x8000080000052fff] (bus address [0x0000-0xffff]) > pci_bus 0003:00: root bus resource [mem 0xc30000000-0xc3fffffff] (bus > address [0xe0000000-0xefffffff]) > pci_bus 0003:00: root bus resource [bus 00] > iommu: Removing device ffe270000.pcie from group 22 > iommu: Adding device 0003:00:00.0 to group 21 > pci 0003:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring > pci 0003:00:00.0: PCI bridge to [bus 01-ff] > PCI: Cannot allocate resource region 0 of device 0000:00:00.0, will remap > PCI: Cannot allocate resource region 0 of device 0001:00:00.0, will remap > PCI: Cannot allocate resource region 2 of device 0001:01:00.0, will remap > PCI: Cannot allocate resource region 5 of device 0001:01:00.0, will remap > PCI: Cannot allocate resource region 6 of device 0001:01:00.0, will remap > PCI: Cannot allocate resource region 0 of device 0001:01:00.1, will remap > PCI: Cannot allocate resource region 0 of device 0002:00:00.0, will remap > PCI: Cannot allocate resource region 0 of device 0003:00:00.0, will remap > pci 0000:00:00.0: BAR 0: no space for [mem size 0x01000000] > pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x01000000] > pci 0000:00:00.0: PCI bridge to [bus 01] > pci 0000:00:00.0: bridge window [io > 0x8000080000010000-0x800008000001ffff] > pci 0000:00:00.0: bridge window [mem 0xc00000000-0xc0fffffff] > pci_bus 0000:00: Some PCI device resources are unassigned, try booting > with pci=realloc > pci 0001:00:00.0: BAR 0: no space for [mem size 0x01000000] > pci 0001:00:00.0: BAR 0: failed to assign [mem size 0x01000000] > pci 0001:00:00.0: BAR 9: no space for [mem size 0x00200000 64bit pref] > pci 0001:00:00.0: BAR 9: failed to assign [mem size 0x00200000 64bit pref] > pci 0001:01:00.0: BAR 2: no space for [mem size 0x00200000 64bit pref] > pci 0001:01:00.0: BAR 2: failed to assign [mem size 0x00200000 64bit pref] > pci 0001:01:00.0: BAR 5: no space for [mem size 0x00040000] > pci 0001:01:00.0: BAR 5: failed to assign [mem size 0x00040000] > pci 0001:01:00.0: BAR 6: no space for [mem size 0x00020000 pref] > pci 0001:01:00.0: BAR 6: failed to assign [mem size 0x00020000 pref] > pci 0001:01:00.1: BAR 0: no space for [mem size 0x00004000 64bit] > pci 0001:01:00.1: BAR 0: failed to assign [mem size 0x00004000 64bit] > pci 0001:00:00.0: PCI bridge to [bus 01] > pci 0001:00:00.0: bridge window [io > 0x8000080000021000-0x8000080000030fff] > pci 0001:00:00.0: bridge window [mem 0xc10000000-0xc1fffffff] > pci_bus 0001:00: Some PCI device resources are unassigned, try booting > with pci=realloc > pci 0002:00:00.0: BAR 0: no space for [mem size 0x01000000] > pci 0002:00:00.0: BAR 0: failed to assign [mem size 0x01000000] > pci 0002:00:00.0: PCI bridge to [bus 01] > pci 0002:00:00.0: bridge window [io > 0x8000080000032000-0x8000080000041fff] > pci 0002:00:00.0: bridge window [mem 0xc20000000-0xc2fffffff] > pci_bus 0002:00: Some PCI device resources are unassigned, try booting > with pci=realloc > pci 0003:00:00.0: BAR 0: no space for [mem size 0x01000000] > pci 0003:00:00.0: BAR 0: failed to assign [mem size 0x01000000] > pci 0003:00:00.0: PCI bridge to [bus 01] > pci 0003:00:00.0: bridge window [io > 0x8000080000043000-0x8000080000052fff] > pci 0003:00:00.0: bridge window [mem 0xc30000000-0xc3fffffff] > pci_bus 0003:00: Some PCI device resources are unassigned, try booting > with pci=realloc > > > >
_______________________________________________ amd-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/amd-gfx
